Eric Lee / smarc-uboot

05 Dec, 2019

1 commit

21 Nov, 2019

2 commits

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     
  • 8d8ee47e0   env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol ... Browse Code »
    24

    Today in initr_reloc_global_data() we use some non-obvious tests to
    determine if we need to relocate the env_addr within gd or not. In
    order to facilitate migration of other symbols to Kconfig we need to
    introduce a new symbol for this particular use case.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Signed-off-by: Tom Rini

    Tom Rini
     

26 Aug, 2019

1 commit

02 Aug, 2019

1 commit

  • 37304aaf6   Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig ... Browse Code »
    4

    This converts the following to Kconfig:
    CONFIG_USE_PREBOOT
    CONFIG_PREBOOT

    Both are together in one commit, since otherwise the former causes kconfig
    to define the latter, which gives duplicate symbol errors.

    Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
    backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

    Signed-off-by: Simon Glass

    Simon Glass
     

30 Apr, 2019

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

28 Feb, 2018

1 commit

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

28 Aug, 2017

1 commit

26 Jul, 2017

1 commit

  • 2be296538   Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig ... Browse Code »
    20

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_MMC
    CONFIG_ENV_IS_IN_NAND
    CONFIG_ENV_IS_IN_UBI
    CONFIG_ENV_IS_NOWHERE

    In fact this already exists for sunxi as a 'choice' config. However not
    all the choices are available in Kconfig yet so we cannot use that. It
    would lead to more than one option being set.

    In addition, one purpose of this series is to allow the environment to be
    stored in more than one place. So the existing choice is converted to a
    normal config allowing each option to be set independently.

    There are not many opportunities for Kconfig updates to reduce the size of
    this patch. This was tested with

    ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

    And then manual updates. This is because for CHAIN_OF_TRUST boards they
    can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
    now.

    Signed-off-by: Simon Glass
    Signed-off-by: Tom Rini

    Simon Glass
     

15 May, 2017

1 commit

  • eb5ba3aef   i2c: Drop use of CONFIG_I2C_HARD ... Browse Code »
    48

    This option is pretty old. It predates CONFIG_SYS_I2C which is itself
    deprecated in favour of driver model. Disable it for all boards.

    Also drop I2C options which depend on this.

    Signed-off-by: Simon Glass

    Simon Glass
     

14 Mar, 2017

1 commit

26 Jan, 2017

1 commit

30 Dec, 2016

1 commit

  • c27269953   mmc: complete unfinished move of CONFIG_MMC ... Browse Code »
    26

    Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
    a Kconfig entry for this option without any actual moves, then
    commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
    instances only for SUNXI.

    We generally do not like such partial moves. This kind of work
    is automated by tools/moveconfig.py, so it is pretty easy to
    complete this move.

    I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
    This shortens the configs and will ease new board porting.

    This commit was created as follows:

    [1] Edit Kconfig (remove the "depends on", add the "default",
    copy the prompt and help message from Linux)

    [2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'

    Signed-off-by: Masahiro Yamada
    Reviewed-by: Jaehoon Chung

    Masahiro Yamada
     

12 Oct, 2016

1 commit

20 Sep, 2016

1 commit

10 Jun, 2016

1 commit

26 Apr, 2016

1 commit

15 Mar, 2016

1 commit

22 Nov, 2015

1 commit

26 Jun, 2015

1 commit

30 Jul, 2014

1 commit

  • dd84058d2   kconfig: add board Kconfig and defconfig files ... Browse Code »

    This commit adds:
    - arch/${ARCH}/Kconfig
    provide a menu to select target boards
    - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
    - configs/${TARGET_BOARD}_defconfig
    default setting of each board

    (This commit was automatically generated by a conversion script
    based on boards.cfg)

    In Linux Kernel, defconfig files are located under
    arch/${ARCH}/configs/ directory.
    It works in Linux Kernel since ARCH is always given from the
    command line for cross compile.

    But in U-Boot, ARCH is not given from the command line.
    Which means we cannot know ARCH until the board configuration is done.
    That is why all the "*_defconfig" files should be gathered into a
    single directory ./configs/.

    Signed-off-by: Masahiro Yamada
    Acked-by: Simon Glass

    Masahiro Yamada