30 Mar, 2020
1 commit
-
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043ASigned-off-by: Biwen Li
Signed-off-by: Priyanka Jain
23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
26 Dec, 2019
1 commit
-
In commit , SPL_FSL_PBL is removed from the configs of
some LayerScape platforms. Actually, SPL_FSL_PBL is needed for SD/NAND
boot on LS1021A/LS1043A/LS1046A to create boot binary having SPL binary
in PBI format concatenated with u-boot binary. SPL_FRAMEWORK is used on
these platforms too.Signed-off-by: Alison Wang
Reviewed-by: Priyanka Jain
05 Dec, 2019
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini
21 Nov, 2019
2 commits
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
08 Oct, 2019
1 commit
-
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng
23 Sep, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
13 Jul, 2019
1 commit
-
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.Signed-off-by: Tom Rini
15 Jun, 2019
1 commit
-
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to KconfigSigned-off-by: Tom Rini
27 May, 2019
1 commit
-
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.Signed-off-by: Tom Rini
30 Apr, 2019
2 commits
-
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.Signed-off-by: Simon Goldschmidt
[trini: Re-run migration]
Signed-off-by: Tom Rini -
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
26 Mar, 2019
1 commit
-
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEEDI use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.Signed-off-by: Patrick Delaunay
03 Mar, 2019
1 commit
-
EFI applications need bounce buffers to work properly on these
platforms.Signed-off-by: Mian Yousaf Kaukab
Reviewed-by: Prabhakar Kushwaha
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
25 Oct, 2018
1 commit
-
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben
Acked-by: Joe Hershberger
20 Oct, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFISigned-off-by: Adam Ford
[trini: Re-migrate]
Signed-off-by: Tom Rini
27 Sep, 2018
1 commit
-
This enables the folowing to Kconfig:
CONFIG_BLK
CONFIG_DM_MMCSigned-off-by: Yinbo Zhu
Reviewed-by: York Sun
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MISC_INIT_RSigned-off-by: Adam Ford
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
27 Jul, 2018
1 commit
-
CONFIG_SPL_FSL_LS_PPA is needed only in case of falcon boot
Support for this is not present in PPA currently, so
removing the default option from defconfigSigned-off-by: Vinitha V Pillai
Signed-off-by: Ruchika Gupta
Reviewed-by: York Sun
11 Jul, 2018
1 commit
-
This patch moves CONFIG_MP to Kconfig
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
04 Jun, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
28 Apr, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_SPIThis partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.Signed-off-by: Adam Ford
Signed-off-by: Tom Rini
09 Apr, 2018
1 commit
-
Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: Mario Six
08 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
11 Feb, 2018
1 commit
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
06 Nov, 2017
1 commit
-
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.Tested-by: Adam Ford #omap3_logic
Signed-off-by: Tom Rini
13 Oct, 2017
1 commit
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
09 Oct, 2017
2 commits
-
Due to a conflict with recent Primary Protected Application (PPA),
PPA cannot be loaded for SPL stage, falcon boot is not enabled by
default. With compatible PPA image, to enable falcon boot, activate
these Kconfig options in defconfig
CONFIG_SPL_FIT=y
CONFIG_SPL_FSL_LS_PPA=y
CONFIG_SPL_GZIP=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_OF_LIBFDT=yBecause environment variables are not avaiable during SPL stage for
SD boot, set "boot_os=y" as default.Signed-off-by: York Sun
Reviewed-by: Simon Glass -
CONFIG_SPL_BOARD_INIT is used for SPL boot. Enable it in defconfig
for LS1043ARDB SPL targets.Signed-off-by: York Sun
23 Sep, 2017
1 commit
-
PPA loading during SPL stage is not required for nornal
SD boot scenario.Signed-off-by: Yangbo Lu
Reviewed-by: York Sun
28 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
15 Aug, 2017
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.Signed-off-by: Sam Protsenko
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini
11 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini