Eric Lee / smarc-uboot

23 Jan, 2020

1 commit

07 Jan, 2020

1 commit

  • eb9124f57   mx6cuboxi: enable OF_CONTROL with DM_MMC and DM_USB ... Browse Code »

    Make first step in DT/DM migration. Enable OF_CONTROL only for the main
    U-Boot image for now.

    Remove mmc_init_main() because board_mmc_init() is not called when
    DM_MMC is enabled.

    DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
    request mandatory. Add code to request/free gpios in platform code.

    MMC devices are now numbered according to DT. The SD card is 1, and eMMC
    is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
    and has_emmc().

    DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
    USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
    DM_REGULATORS for the USB power controller. This allows us to drop
    board_ehci_hcd_init() and setup_usb().

    Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
    incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
    depends on DT. Instead, we take one "fully featured" DT of each variant.
    That should be enough to boot from both SD card and eMMC.

    Since we don't select the exact DT, override the generic
    show_board_info() that shows the selected DT 'model' field.

    Signed-off-by: Baruch Siach
    Reviewed-by: Fabio Estevam

    Baruch Siach
     

05 Dec, 2019

1 commit

21 Nov, 2019

2 commits

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     
  • 8d8ee47e0   env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol ... Browse Code »
    24

    Today in initr_reloc_global_data() we use some non-obvious tests to
    determine if we need to relocate the env_addr within gd or not. In
    order to facilitate migration of other symbols to Kconfig we need to
    introduce a new symbol for this particular use case.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Signed-off-by: Tom Rini

    Tom Rini
     

23 Sep, 2019

1 commit

24 Aug, 2019

1 commit

02 Aug, 2019

1 commit

  • 37304aaf6   Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig ... Browse Code »
    4

    This converts the following to Kconfig:
    CONFIG_USE_PREBOOT
    CONFIG_PREBOOT

    Both are together in one commit, since otherwise the former causes kconfig
    to define the latter, which gives duplicate symbol errors.

    Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
    backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

    Signed-off-by: Simon Glass

    Simon Glass
     

23 Jun, 2019

1 commit

30 Apr, 2019

2 commits

14 Apr, 2019

1 commit

01 Feb, 2019

1 commit

19 Jan, 2019

1 commit

  • 2acc24fc2   Kconfig: Migrate BOUNCE_BUFFER ... Browse Code »

    The bounce buffer is used by a few drivers (most of the MMC drivers)
    to overcome limitations in their respective DMA implementation.

    This moves the configuration to Kconfig and makes it user-selectable
    (even though it will be a required feature to make those drivers
    work): the expected usage is for drivers depending on this to 'select'
    it unconditionally from their respective Kconfig (see follow-up
    patches).

    This commit includes a full migration using moveconfig.py to ensure
    that each commit compiles. To ensure bisectability we update
    dependencies of various drivers to now select BOUNCE_BUFFER when needed.

    [trini: Squash all patches to ensure bisectability]
    Signed-off-by: Tom Rini
    Signed-off-by: Philipp Tomsich
    Reviewed-by: Otavio Salvador [dw_mmc portion]
    Reviewed-by: Fabio Estevam [mxsmmc portion]
    Reviewed-by: Simon Glass [tegra portion]

    Philipp Tomsich
     

08 Jan, 2019

1 commit

18 Aug, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

04 Jun, 2018

1 commit

09 Apr, 2018

2 commits

08 Apr, 2018

1 commit

24 Feb, 2018

1 commit

  • d021e9421   Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_BOOTP_BOOTPATH
    CONFIG_BOOTP_DNS
    CONFIG_BOOTP_GATEWAY
    CONFIG_BOOTP_HOSTNAME
    CONFIG_BOOTP_PXE
    CONFIG_BOOTP_SUBNETMASK
    CONFIG_CMDLINE_EDITING
    CONFIG_AUTO_COMPLETE
    CONFIG_SYS_LONGHELP
    CONFIG_SUPPORT_RAW_INITRD
    CONFIG_ENV_VARS_UBOOT_CONFIG

    Signed-off-by: Adam Ford
    [trini: Re-run the migration]
    Signed-off-by: Tom Rini

    Adam Ford
     

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

19 Dec, 2017

1 commit

13 Dec, 2017

1 commit

27 Nov, 2017

1 commit

20 Nov, 2017

1 commit

18 Nov, 2017

1 commit

  • b6251db8c   Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND ... Browse Code »
    54

    We first introduce CONFIG_USE_BOOTCOMMAND, similar to
    CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
    CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
    scheme around this usage, and these have been defered for the moment so
    that platform maintainers can work on a migration plan.

    Signed-off-by: Tom Rini
    Reviewed-by: Lukasz Majewski

    Tom Rini
     

31 Oct, 2017

1 commit

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

27 Sep, 2017

1 commit

02 Sep, 2017

1 commit

  • ecad7051b   configs: Migrate all of the existing USB symbols, except fastboot ... Browse Code »
    20

    This syncs all of the currently Kconfig'd symbols out of the headers and
    into the defconfig files. This has two exceptions, first am335x_evm
    needs to be converted to DM in SPL and then it can stop undef'ing
    CONFIG_DM_USB. Leaving this as-is results in a build failure, and
    without work, run time failure. The other case is am43xx_evm.h and in
    turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
    host mode in SPL, but still desire to have gadget mode in U-Boot proper.

    Signed-off-by: Tom Rini

    Tom Rini
     

28 Aug, 2017

1 commit

15 Aug, 2017

1 commit

08 Aug, 2017

1 commit

26 Jul, 2017

1 commit

  • 2be296538   Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig ... Browse Code »
    20

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_MMC
    CONFIG_ENV_IS_IN_NAND
    CONFIG_ENV_IS_IN_UBI
    CONFIG_ENV_IS_NOWHERE

    In fact this already exists for sunxi as a 'choice' config. However not
    all the choices are available in Kconfig yet so we cannot use that. It
    would lead to more than one option being set.

    In addition, one purpose of this series is to allow the environment to be
    stored in more than one place. So the existing choice is converted to a
    normal config allowing each option to be set independently.

    There are not many opportunities for Kconfig updates to reduce the size of
    this patch. This was tested with

    ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

    And then manual updates. This is because for CHAIN_OF_TRUST boards they
    can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
    now.

    Signed-off-by: Simon Glass
    Signed-off-by: Tom Rini

    Simon Glass
     

14 Jul, 2017

1 commit

  • 651782a08   mx6cuboxi: Move CONFIG_CMD_SATA to Kconfig ... Browse Code »

    Move CONFIG_CMD_SATA option to Kconfig to fix the following build
    error:

    In file included from include/configs/mx6cuboxi.h:137:0,
    from include/config.h:7,
    from include/common.h:21,
    from common/env_common.c:11:
    include/config_distro_bootcmd.h:161:2: error: expected '}' before 'BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA'
    BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA

    Reported-by: Stefano Babic
    Signed-off-by: Fabio Estevam

    Fabio Estevam
     

12 Jul, 2017

1 commit

  • 552a848e4   imx: reorganize IMX code as other SOCs ... Browse Code »

    Change is consistent with other SOCs and it is in preparation
    for adding SOMs. SOC's related files are moved from cpu/ to
    mach-imx/.

    This change is also coherent with the structure in kernel.

    Signed-off-by: Stefano Babic

    CC: Fabio Estevam
    CC: Akshay Bhat
    CC: Ken Lin
    CC: Marek Vasut
    CC: Heiko Schocher
    CC: "Sébastien Szymanski"
    CC: Christian Gmeiner
    CC: Stefan Roese
    CC: Patrick Bruenn
    CC: Troy Kisky
    CC: Nikita Kiryanov
    CC: Otavio Salvador
    CC: "Eric Bénard"
    CC: Jagan Teki
    CC: Ye Li
    CC: Peng Fan
    CC: Adrian Alonso
    CC: Alison Wang
    CC: Tim Harvey
    CC: Martin Donnelly
    CC: Marcin Niestroj
    CC: Lukasz Majewski
    CC: Adam Ford
    CC: "Albert ARIBAUD (3ADEV)"
    CC: Boris Brezillon
    CC: Soeren Moch
    CC: Richard Hu
    CC: Wig Cheng
    CC: Vanessa Maegima
    CC: Max Krummenacher
    CC: Stefan Agner
    CC: Markus Niebel
    CC: Breno Lima
    CC: Francesco Montefoschi
    CC: Jaehoon Chung
    CC: Scott Wood
    CC: Joe Hershberger
    CC: Anatolij Gustschin
    CC: Simon Glass
    CC: "Andrew F. Davis"
    CC: "Łukasz Majewski"
    CC: Patrice Chotard
    CC: Nobuhiro Iwamatsu
    CC: Hans de Goede
    CC: Masahiro Yamada
    CC: Stephen Warren
    CC: Andre Przywara
    CC: "Álvaro Fernández Rojas"
    CC: York Sun
    CC: Xiaoliang Yang
    CC: Chen-Yu Tsai
    CC: George McCollister
    CC: Sven Ebenfeld
    CC: Filip Brozovic
    CC: Petr Kulhavy
    CC: Eric Nelson
    CC: Bai Ping
    CC: Anson Huang
    CC: Sanchayan Maity
    CC: Lokesh Vutla
    CC: Patrick Delaunay
    CC: Gary Bisson
    CC: Alexander Graf
    CC: u-boot@lists.denx.de
    Reviewed-by: Fabio Estevam
    Reviewed-by: Christian Gmeiner

    Stefano Babic
     

19 Jun, 2017

1 commit

23 May, 2017

1 commit

  • 7a01f3c6f   Convert CONFIG_CMD_HDMIDETECT to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_CMD_HDMIDETECT

    Note that we cannot do 'default y if VIDEO' because this option is only
    enabled for a small subset of mx6 boards. Also this command is is not a
    great implementation (it doesn't use driver model).

    Signed-off-by: Simon Glass
    Reviewed-by: Tom Rini

    Simon Glass