Eric Lee / smarc-uboot

21 Nov, 2019

1 commit

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     

27 May, 2019

1 commit

26 Mar, 2019

1 commit

  • 14453fbfa   Convert CONFIG_SF_DEFAULT_* to Kconfig ... Browse Code »
    36

    This converts the following to Kconfig:
    CONFIG_SF_DEFAULT_BUS
    CONFIG_SF_DEFAULT_CS
    CONFIG_SF_DEFAULT_MODE
    CONFIG_SF_DEFAULT_SPEED

    I use moveconfig script and then manual check on generated u-boot.cfg
    to solve the remaining issue.

    Signed-off-by: Patrick Delaunay

    Patrick Delaunay
     

03 Mar, 2019

1 commit

07 Dec, 2018

1 commit

  • 50e2d41f6   armv8: ls1046aqds: Add TFABOOT support ... Browse Code »

    TFABOOT support includes:
    - ls1046aqds_tfa_defconfig to be loaded by trusted firmware
    - environment address and size changes for TFABOOT
    - FMAN address changes for TFABOOT
    - define BOOTCOMMAND for TFABOOT

    Signed-off-by: Pankit Garg
    Signed-off-by: Vinitha V Pillai
    Signed-off-by: Rajesh Bhagat
    Reviewed-by: York Sun

    Rajesh Bhagat
     

20 Oct, 2018

1 commit

18 Aug, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

07 May, 2018

1 commit

  • 83d290c56   SPDX: Convert all of our single license tags to Linux Kernel style ... Browse Code »
    56

    When U-Boot started using SPDX tags we were among the early adopters and
    there weren't a lot of other examples to borrow from. So we picked the
    area of the file that usually had a full license text and replaced it
    with an appropriate SPDX-License-Identifier: entry. Since then, the
    Linux Kernel has adopted SPDX tags and they place it as the very first
    line in a file (except where shebangs are used, then it's second line)
    and with slightly different comment styles than us.

    In part due to community overlap, in part due to better tag visibility
    and in part for other minor reasons, switch over to that style.

    This commit changes all instances where we have a single declared
    license in the tag as both the before and after are identical in tag
    contents. There's also a few places where I found we did not have a tag
    and have introduced one.

    Signed-off-by: Tom Rini

    Tom Rini
     

24 Feb, 2018

1 commit

  • d021e9421   Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_BOOTP_BOOTPATH
    CONFIG_BOOTP_DNS
    CONFIG_BOOTP_GATEWAY
    CONFIG_BOOTP_HOSTNAME
    CONFIG_BOOTP_PXE
    CONFIG_BOOTP_SUBNETMASK
    CONFIG_CMDLINE_EDITING
    CONFIG_AUTO_COMPLETE
    CONFIG_SYS_LONGHELP
    CONFIG_SUPPORT_RAW_INITRD
    CONFIG_ENV_VARS_UBOOT_CONFIG

    Signed-off-by: Adam Ford
    [trini: Re-run the migration]
    Signed-off-by: Tom Rini

    Adam Ford
     

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

18 Jan, 2018

1 commit

19 Dec, 2017

1 commit

13 Dec, 2017

2 commits

06 Nov, 2017

1 commit

27 Oct, 2017

3 commits

09 Oct, 2017

1 commit

04 Sep, 2017

2 commits

  • e090579d0   include/configs: remove numerous CONFIG_SYS_BARGSIZE definitions ... Browse Code »

    This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
    equal to CONFIG_SYS_CBSIZE in numerous configuration files.

    We remove such definitions in two situations:

    - CONFIG_SYS_CBSIZE is otherwise not defined in the board
    configuration file, which means the default value of
    CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
    of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
    larger.

    - CONFIG_SYS_CBSIZE is defined in the board configuration file, but
    to a value equal or less than 512. In this case, the default value
    of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
    is equal or larger.

    Signed-off-by: Thomas Petazzoni
    Reviewed-by: Tom Rini

    Thomas Petazzoni
     
  • 432e39806   include/configs: drop default definitions of CONFIG_SYS_PBSIZE ... Browse Code »
    1

    Now that the fallback value of CONFIG_SYS_PBSIZE in
    include/config_fallbacks.h has been adjusted, remove its definition
    from a large number of board configuration files.

    Signed-off-by: Thomas Petazzoni
    Reviewed-by: Tom Rini

    Thomas Petazzoni
     

02 Sep, 2017

1 commit

  • ecad7051b   configs: Migrate all of the existing USB symbols, except fastboot ... Browse Code »
    20

    This syncs all of the currently Kconfig'd symbols out of the headers and
    into the defconfig files. This has two exceptions, first am335x_evm
    needs to be converted to DM in SPL and then it can stop undef'ing
    CONFIG_DM_USB. Leaving this as-is results in a build failure, and
    without work, run time failure. The other case is am43xx_evm.h and in
    turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
    host mode in SPL, but still desire to have gadget mode in U-Boot proper.

    Signed-off-by: Tom Rini

    Tom Rini
     

08 Aug, 2017

1 commit

02 Aug, 2017

1 commit

01 Aug, 2017

3 commits

29 Jul, 2017

1 commit

26 Jul, 2017

3 commits

  • 91c868fe7   Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig ... Browse Code »
    20

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_SPI_FLASH

    Signed-off-by: Simon Glass

    Simon Glass
     
  • 85fc970d7   Convert CONFIG_ENV_IS_IN_FLASH to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_FLASH

    Signed-off-by: Simon Glass

    Simon Glass
     
  • 2be296538   Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig ... Browse Code »
    20

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_MMC
    CONFIG_ENV_IS_IN_NAND
    CONFIG_ENV_IS_IN_UBI
    CONFIG_ENV_IS_NOWHERE

    In fact this already exists for sunxi as a 'choice' config. However not
    all the choices are available in Kconfig yet so we cannot use that. It
    would lead to more than one option being set.

    In addition, one purpose of this series is to allow the environment to be
    stored in more than one place. So the existing choice is converted to a
    normal config allowing each option to be set independently.

    There are not many opportunities for Kconfig updates to reduce the size of
    this patch. This was tested with

    ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

    And then manual updates. This is because for CHAIN_OF_TRUST boards they
    can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
    now.

    Signed-off-by: Simon Glass
    Signed-off-by: Tom Rini

    Simon Glass
     

12 Jul, 2017

1 commit

24 May, 2017

1 commit

07 Apr, 2017

1 commit

  • 01abae4d0   Remove various unused interrupt related code ... Browse Code »

    With d53ecad92f06 some unused interrupt related code was removed.
    However all of these options are currently unused. Rather than migrate
    some of these options to Kconfig we just remove the code in question.

    The only related code changes here are that in some cases we use
    CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
    and move the value local to the code in question.

    Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
    Signed-off-by: Tom Rini

    Tom Rini
     

29 Mar, 2017

1 commit

14 Mar, 2017

1 commit

13 Feb, 2017

1 commit

  • e856bdcfb   flash: complete CONFIG_SYS_NO_FLASH move with renaming ... Browse Code »
    20

    We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
    not completed. Finish this work by the tool.

    During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
    Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
    than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
    make the code more readable. Besides, negative meaning symbols do
    not fit in obj-$(CONFIG_...) style Makefiles.

    This commit was created as follows:

    [1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

    [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

    [3] Rename the instances in defconfigs by the following:
    find . -path './configs/*_defconfig' | xargs sed -i \
    -e '/CONFIG_SYS_NO_FLASH=y/d' \
    -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

    [4] Change the conditionals by the following:
    find . -name '*.[ch]' | xargs sed -i \
    -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
    -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
    -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
    -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

    [5] Modify the following manually
    - Rename the rest of instances
    - Remove the description from README
    - Create the new Kconfig entry in drivers/mtd/Kconfig
    - Remove the old Kconfig entry from common/Kconfig
    - Remove the garbage comments from include/configs/*.h

    Signed-off-by: Masahiro Yamada

    Masahiro Yamada
     

04 Feb, 2017

1 commit

  • c83a824e6   Merge git://git.denx.de/u-boot-fsl-qoriq ... Browse Code »

    Signed-off-by: Tom Rini

    Conflicts:
    configs/ls1046aqds_defconfig
    configs/ls1046aqds_nand_defconfig
    configs/ls1046aqds_qspi_defconfig
    configs/ls1046aqds_sdcard_ifc_defconfig
    configs/ls1046aqds_sdcard_qspi_defconfig
    configs/ls1046ardb_emmc_defconfig
    configs/ls1046ardb_qspi_defconfig
    configs/ls1046ardb_sdcard_defconfig

    Tom Rini
     

28 Jan, 2017

1 commit