Eric Lee / smarc-uboot

26 Mar, 2019

1 commit

  • 14453fbfa   Convert CONFIG_SF_DEFAULT_* to Kconfig ... Browse Code »
    36

    This converts the following to Kconfig:
    CONFIG_SF_DEFAULT_BUS
    CONFIG_SF_DEFAULT_CS
    CONFIG_SF_DEFAULT_MODE
    CONFIG_SF_DEFAULT_SPEED

    I use moveconfig script and then manual check on generated u-boot.cfg
    to solve the remaining issue.

    Signed-off-by: Patrick Delaunay

    Patrick Delaunay
     

14 Feb, 2019

1 commit

  • d13f92b74   ARM: zynq: Run distribution boot commands first ... Browse Code »

    This patch is doing two things.
    1. Exchanging order of boot commands. distro_bootcmd is run first
    followed by Xilinx boot command.
    2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
    creating Xilinx distribution bootcommand and wiring it as the last
    bootcommand.

    QSPI, NAND distribution boot command will be added later.

    Signed-off-by: Michal Simek

    Michal Simek
     

07 Feb, 2019

1 commit

  • 6d8251783   configs: Don't use SPI_FLASH_BAR as default ... Browse Code »
    12

    Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
    don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
    4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
    renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
    not break functionality.

    Signed-off-by: Vignesh R
    Tested-by: Simon Goldschmidt
    Tested-by: Stefan Roese
    Tested-by: Horatiu Vultur
    Reviewed-by: Jagan Teki
    Tested-by: Jagan Teki #zynq-microzed

    Vignesh R
     

01 Feb, 2019

1 commit

04 Sep, 2018

1 commit

18 Aug, 2018

1 commit

06 Aug, 2018

1 commit

11 May, 2018

1 commit

  • 0b4b82ad1   arm: zynq: Remove checkboard and enable DISPLAY_CPUINFO ... Browse Code »

    Now that showing silicon version is part of the CPU
    info display, let's remove checkboard().

    Note that the generic show_board_info() will still
    show the DT 'model' property. For instance:

    U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)

    CPU: Zynq 7z045
    Silicon: v1.0
    Model: Zynq ZC706 Development Board
    I2C: ready

    Based on patches from Ariel D'Alessandro ,
    and Ezequiel Garcia

    mini configuration doesn't need to show this information.

    Signed-off-by: Michal Simek

    Michal Simek
     

28 Apr, 2018

1 commit

17 Apr, 2018

1 commit

  • 4f67b93fb   part: Disable CONFIG_SPL_ISO_PARTITION by default ... Browse Code »

    We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
    could load distro images that usually get shipped as iso images. These images
    usually come with a board agnostic boot environment.

    However, there is very little point in having ISO support enabled (for anyone
    really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
    is board specific. So the fact that we enable ISO support in U-Boot proper does
    not mean at all that we want ISO support in U-Boot SPL.

    Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
    all those default configs that disabled SPL ISO support.

    Signed-off-by: Alexander Graf

    Alexander Graf
     

12 Apr, 2018

1 commit

23 Mar, 2018

1 commit

01 Mar, 2018

1 commit

23 Feb, 2018

1 commit

30 Jan, 2018

6 commits

15 Dec, 2017

1 commit

28 Nov, 2017

4 commits

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

28 Aug, 2017

1 commit

26 Jul, 2017

1 commit

  • 2be296538   Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig ... Browse Code »
    20

    This converts the following to Kconfig:
    CONFIG_ENV_IS_IN_MMC
    CONFIG_ENV_IS_IN_NAND
    CONFIG_ENV_IS_IN_UBI
    CONFIG_ENV_IS_NOWHERE

    In fact this already exists for sunxi as a 'choice' config. However not
    all the choices are available in Kconfig yet so we cannot use that. It
    would lead to more than one option being set.

    In addition, one purpose of this series is to allow the environment to be
    stored in more than one place. So the existing choice is converted to a
    normal config allowing each option to be set independently.

    There are not many opportunities for Kconfig updates to reduce the size of
    this patch. This was tested with

    ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

    And then manual updates. This is because for CHAIN_OF_TRUST boards they
    can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
    now.

    Signed-off-by: Simon Glass
    Signed-off-by: Tom Rini

    Simon Glass
     

04 Jun, 2017

1 commit

  • 91d27a17c   Kconfig: Migrate FS_FAT / FAT_WRITE ... Browse Code »

    Now that these symbols are in Kconfig, migrate all users. Use imply on
    a number of platforms that default to having this enabled. As part of
    this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

    Signed-off-by: Tom Rini

    Tom Rini
     

22 May, 2017

1 commit

13 Feb, 2017

1 commit

  • e856bdcfb   flash: complete CONFIG_SYS_NO_FLASH move with renaming ... Browse Code »
    20

    We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
    not completed. Finish this work by the tool.

    During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
    Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
    than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
    make the code more readable. Besides, negative meaning symbols do
    not fit in obj-$(CONFIG_...) style Makefiles.

    This commit was created as follows:

    [1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

    [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

    [3] Rename the instances in defconfigs by the following:
    find . -path './configs/*_defconfig' | xargs sed -i \
    -e '/CONFIG_SYS_NO_FLASH=y/d' \
    -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

    [4] Change the conditionals by the following:
    find . -name '*.[ch]' | xargs sed -i \
    -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
    -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
    -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
    -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

    [5] Modify the following manually
    - Rename the rest of instances
    - Remove the description from README
    - Create the new Kconfig entry in drivers/mtd/Kconfig
    - Remove the old Kconfig entry from common/Kconfig
    - Remove the garbage comments from include/configs/*.h

    Signed-off-by: Masahiro Yamada

    Masahiro Yamada
     

24 Jan, 2017

1 commit

22 Jan, 2017

1 commit

10 Jan, 2017

1 commit

30 Dec, 2016

1 commit

  • c27269953   mmc: complete unfinished move of CONFIG_MMC ... Browse Code »
    26

    Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
    a Kconfig entry for this option without any actual moves, then
    commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
    instances only for SUNXI.

    We generally do not like such partial moves. This kind of work
    is automated by tools/moveconfig.py, so it is pretty easy to
    complete this move.

    I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
    This shortens the configs and will ease new board porting.

    This commit was created as follows:

    [1] Edit Kconfig (remove the "depends on", add the "default",
    copy the prompt and help message from Linux)

    [2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'

    Signed-off-by: Masahiro Yamada
    Reviewed-by: Jaehoon Chung

    Masahiro Yamada
     

15 Oct, 2016

1 commit

12 Oct, 2016

1 commit

17 Sep, 2016

1 commit

02 Aug, 2016

1 commit

22 Jul, 2016

1 commit