05 Mar, 2018
1 commit
-
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.Signed-off-by: Faiz Abbas
23 Feb, 2018
1 commit
-
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.Fixes: bfebc8c965e4 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis
Reviewed-by: Lokesh Vutla
19 Feb, 2018
1 commit
-
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")Signed-off-by: Kishon Vijay Abraham I
Signed-off-by: Jean-Jacques Hiblot
15 Feb, 2018
1 commit
-
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.Signed-off-by: Faiz Abbas
Reviewed-by: Marek Vasut
Reviewed-by: Bin Meng
08 Feb, 2018
1 commit
-
Add pinmux for QSPI pins on K2G ICE board.
Signed-off-by: Vignesh R
28 Jan, 2018
1 commit
-
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.Signed-off-by: Faiz Abbas
20 Jan, 2018
11 commits
-
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 BeagleBoard(s). -
Add initial dts support for am574x-idk
Signed-off-by: Lokesh Vutla
-
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed ".Signed-off-by: Lokesh Vutla
-
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.Signed-off-by: Lokesh Vutla
Signed-off-by: Krunal Bhargav -
Update prcm, voltages and pinmux support for am574x-idk.
Signed-off-by: Lokesh Vutla
-
am574x-idk is a board based on TI's am574 processor
Add eeprom support.Signed-off-by: Lokesh Vutla
-
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPsBoth the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.Signed-off-by: Lokesh Vutla
-
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.Signed-off-by: Lokesh Vutla
Reviewed-by: Tom Rini -
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.Signed-off-by: Tomi Valkeinen
-
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang
Signed-off-by: Lokesh Vutla -
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.Reviewed-by: Lokesh Vutla
Signed-off-by: Vignesh R
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr
Signed-off-by: Lokesh Vutla
Signed-off-by: Faiz Abbas
01 Jan, 2018
1 commit
-
This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.Signed-off-by: Derald D. Woods
04 Dec, 2017
1 commit
-
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon
Date: Fri Aug 4 17:29:10 2017 +0200mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.Signed-off-by: Masahiro Yamada
26 Nov, 2017
1 commit
-
When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:/*
* Reset any devices that may be in a bad state when applying
* the power. This is a __weak function. Resetting of the devices
* should occur in the board file of the device.
*/
for (i = 0; i < dev->maxchild; i++)
usb_hub_reset_devices(i + 1);This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.Existing implementations are changed to accept and ignore the new
parameter.Signed-off-by: Philipp Tomsich
Tested-by: Jakob Unterwurzacher
21 Nov, 2017
1 commit
-
We don't want this build anymore.
Acked-by: Lokesh Vutla
Signed-off-by: Tom Rini
17 Nov, 2017
1 commit
-
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.Signed-off-by: Keerthy
Reviewed-by: Tom Rini
27 Oct, 2017
1 commit
-
This comment creates a wrong entry in config_whitelist.txt.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.Signed-off-by: Masahiro Yamada
06 Oct, 2017
1 commit
-
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini
Reviewed-by: Simon Glass
13 Sep, 2017
2 commits
-
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.Signed-off-by: Vishal Mahaveer
Reviewed-by: Lokesh Vutla -
The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.Signed-off-by: Andrew F. Davis
12 Sep, 2017
10 commits
-
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FITSigned-off-by: Lokesh Vutla
Reviewed-by: Tom Rini -
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.Signed-off-by: Steve Kipisz
Signed-off-by: Lokesh Vutla
Reviewed-by: Tom Rini -
Add support for selecting proper dtb for
dra76x u-boot from FIT.Signed-off-by: Lokesh Vutla
Reviewed-by: Tom Rini -
ldo4 is used to poweron mmc on dra76-evm. Enable it.
Reviewed-by: Tom Rini
Signed-off-by: Lokesh Vutla -
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini
Signed-off-by: Vignesh R
Signed-off-by: Lokesh Vutla -
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.Reviewed-by: Tom Rini
Signed-off-by: Lokesh Vutla -
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.Reviewed-by: Tom Rini
Signed-off-by: Keerthy
Signed-off-by: Lokesh Vutla -
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom supportReviewed-by: Tom Rini
Signed-off-by: Lokesh Vutla -
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.Reviewed-by: Tom Rini
Signed-off-by: Lokesh Vutla -
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.Reviewed-by: Tom Rini
Signed-off-by: Lokesh Vutla
04 Sep, 2017
1 commit
-
- Pass MTDPARTS kernel arguments to kernel
- Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND"
- Call 'usb_stop' on kernel start
- Update Falcon mode setup to match other OMAP3 boards
- Use "uEnv.txt" as boot script instead of "boot.scr"
16 Aug, 2017
3 commits
-
Rename this function for consistency with env_get().
Signed-off-by: Simon Glass
-
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.Suggested-by: Wolfgang Denk
Signed-off-by: Simon Glass -
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.Suggested-by: Wolfgang Denk
Signed-off-by: Simon Glass
