26 Mar, 2019
1 commit
-
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODEMost of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.Signed-off-by: Patrick Delaunay
07 Feb, 2019
1 commit
-
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.Signed-off-by: Vignesh R
Tested-by: Simon Goldschmidt
Tested-by: Stefan Roese
Tested-by: Horatiu Vultur
Reviewed-by: Jagan Teki
Tested-by: Jagan Teki #zynq-microzed
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMACSigned-off-by: Adam Ford
Acked-by: Jagan Teki
Acked-by: Joe Hershberger
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
04 Jun, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
15 May, 2018
1 commit
-
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.Move it to the defconfigs for all boards.
Signed-off-by: Mario Six
Acked-by: Joe Hershberger
17 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
12 Apr, 2018
1 commit
-
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.Signed-off-by: Marek Vasut
Cc: Tom Rini
09 Apr, 2018
1 commit
-
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six
[trini: Re-run migration]
Signed-off-by: Tom Rini
08 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
14 Feb, 2018
1 commit
-
Signed-off-by: Tuomas Tynkkynen
11 Feb, 2018
1 commit
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
26 Sep, 2017
1 commit
-
This converts the following to Kconfig:
CONFIG_MVNETASigned-off-by: Chris Packham
Reviewed-by: Simon Glass
Signed-off-by: Stefan Roese
15 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
09 Aug, 2017
1 commit
-
Reviewed-by: Joe Hershberger
Signed-off-by: Tom Rini
08 Aug, 2017
1 commit
-
Signed-off-by: Alexandru Gagniuc
Acked-by: Joe Hershberger
19 Jun, 2017
1 commit
-
Signed-off-by: Tom Rini
14 Mar, 2017
1 commit
-
Signed-off-by: Tom Rini
30 Dec, 2016
1 commit
-
Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada
Reviewed-by: Jaehoon Chung
24 Oct, 2016
1 commit
-
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIETSigned-off-by: Simon Glass
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini
12 Oct, 2016
1 commit
-
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.Signed-off-by: Lokesh Vutla
Signed-off-by: Tom Rini
20 Sep, 2016
1 commit
-
This reverts commit 90c08d9e08c7a108ab904f3bbdeb558081757892.
I took a closer look at this after the commit was applied, and found
CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is
actually too big for some boards. Perhaps 0x800 is enough, but the
situation varies board by board.Let's postpone our decision until we come up with a better idea.
Signed-off-by: Masahiro Yamada
Reviewed-by: Simon Glass
17 Sep, 2016
7 commits
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass
-
Move the SPL settings into common/spl where most of the SPL code is kept.
Signed-off-by: Simon Glass
07 Sep, 2016
1 commit
-
If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind
several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently
not enough. Increase the default to 0x2000 for the case. This
will be helpful for shorter defconfigs.Signed-off-by: Masahiro Yamada
Reviewed-by: Stefan Roese
Reviewed-by: Simon Glass
10 Jun, 2016
1 commit
-
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.Signed-off-by: Heiko Schocher
Reviewed-by: Tom Rini
Acked-by: Viresh Kumar
Acked-by: Igor Grinberg
26 Apr, 2016
2 commits
-
Update the config.h and defconfig files for the commands that 8e3c036
converted over to KconfigSigned-off-by: Tom Rini
-
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.Signed-off-by: Tom Rini
14 Jan, 2016
2 commits
-
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.Signed-off-by: Stefan Roese
Cc: Luka Perkov -
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.Signed-off-by: Stefan Roese
Cc: Luka Perkov
Cc: Dirk Eibach
Cc: Simon Glass
25 Nov, 2015
1 commit
-
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.Signed-off-by: Bin Meng
22 Nov, 2015
1 commit
-
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: Thomas Chou
21 Oct, 2015
1 commit
-
This patch adds driver model support for some Marvell MVEBU SoC's. Including
Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now
selected automatically for MVEBU platforms.With this DM support now available for MVEBU, hardcoding the base addresses
and other information is not necessary any more. Probing should be done
by using the values provided via the device tree now instead. For this
the driver also need to be converted to DM. Patches for some of the drivers
will follow.Signed-off-by: Stefan Roese
Cc: Simon Glass
Cc: Luka Perkov