27 Nov, 2018
1 commit
-
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.So remove the dead instances of CONFIG_HARD_SPI, and related
code.Signed-off-by: Jagan Teki
03 Oct, 2018
1 commit
-
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini
23 Sep, 2018
2 commits
-
Caches should be configured to mode CONF_CM_CACHABLE_NONCOHERENT
(or CONF_CM_CACHABLE_COW when a CM is available). There is no
need to make this configurable.Signed-off-by: Daniel Schwierzeck
-
Some MIPS systems store some board-specific boot configuration
in the U-Boot binary at offset 0x10. This is used by Malta boards
and by Lantiq/Intel SoC's when booting from parallel NOR flash.Convert the hard-coded values to Kconfig options to remove such
board-specific stuff out of the generic start.S code. This also
deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG.Signed-off-by: Daniel Schwierzeck
20 Sep, 2018
1 commit
-
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.Signed-off-by: Miquel Raynal
11 Sep, 2018
1 commit
-
You do not need to use the typedefs provided by compiler.
Our compilers are either IPL32 or LP64. Hence, U-Boot can/should
always use int-ll64.h typedefs like Linux kernel, whatever the
typedefs the compiler internally uses.Signed-off-by: Masahiro Yamada
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMACSigned-off-by: Adam Ford
Acked-by: Jagan Teki
Acked-by: Joe Hershberger
11 Aug, 2018
1 commit
-
Describe the interface of environment variable callback functions.
Signed-off-by: Heinrich Schuchardt
23 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICESigned-off-by: Adam Ford
27 Jun, 2018
1 commit
-
Add the config option `CONFIG_SPL_NAND_IDENT` for using the NAND chip ID list
to identify the NAND flash in SPL.Signed-off-by: Jörg Krause
29 May, 2018
1 commit
-
This was being used by some Marvell boards to enable some file system
related features (many of which have already been moved to Kconfig).
Make the future migration of the final 2 or 3 config options easier by
expanding #define CONFIG_SYS_MVFS into the options that it enables and
remove CONFIG_SYS_MVFS.Signed-off-by: Chris Packham
Reviewed-by: Simon Glass
Reviewed-by: Stefan Roese
Signed-off-by: Stefan Roese
24 May, 2018
2 commits
-
Rename CONFIG_FIT_SPL_PRINT to CONFIG_SPL_FIT_PRINT and add Kconfig
entry for it.Signed-off-by: Marek Vasut
Cc: Pantelis Antoniou
Cc: Simon Glass
Reviewed-by: Simon Glass -
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.Signed-off-by: Alex Kiernan
07 May, 2018
1 commit
-
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.Signed-off-by: Tom Rini
28 Apr, 2018
1 commit
-
This converts IMAGE_FORMAT_LEGACY to Kconfig
Signed-off-by: Alex Kiernan
Reviewed-by: Tom Rini
09 Apr, 2018
3 commits
-
CONFIG_VERSION_VARIABLE had already been mostly migrated to Kconfig,
but two headers still referenced it. Also set defaults so that
most of the defconfigs inherit the default rather than needing it
to be set explicitly.Signed-off-by: Alex Kiernan
Reviewed-by: Petr Vorel -
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski
Reviewed-by: Petr Vorel
Reviewed-by: Petr Vorel -
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini
07 Apr, 2018
1 commit
-
This converts CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC to Kconfig
Signed-off-by: Alex Kiernan
24 Mar, 2018
2 commits
-
Signed-off-by: Petr Vorel
-
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.Signed-off-by: Petr Vorel
Cc: Joe Hershberger
Cc: Heiko Schocher
14 Mar, 2018
1 commit
-
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.After the changes the suspicious defconfigs passes building.
Signed-off-by: Stefan Mavrodiev
Acked-by: Maxime Ripard
[jagan: rebased on master]
Signed-off-by: Jagan Teki
Reviewed-by: Jagan Teki
24 Feb, 2018
7 commits
-
Integrate Boot counter for Atmel AT91SAM9XE into Kconfig
Reviewed-by: Lukasz Majewski
Signed-off-by: Alex Kiernan -
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_EXTSigned-off-by: Alex Kiernan
-
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_I2CSigned-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski -
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_RAMSigned-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski -
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENVSigned-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski -
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_AM33XXReviewed-by: Lukasz Majewski
Reviewed-by: Hannes Schmelzer
Acked-by: Hannes Schmelzer
Signed-off-by: Alex Kiernan -
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIGSigned-off-by: Adam Ford
[trini: Re-run the migration]
Signed-off-by: Tom Rini
22 Feb, 2018
1 commit
-
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`Signed-off-by: Marek Vasut
Cc: Lukasz Majewski
15 Feb, 2018
2 commits
-
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMITSigned-off-by: Lukasz Majewski
Tested-by: Alex Kiernan
Reviewed-by: Hannes Schmelzer
Acked-by: Hannes Schmelzer -
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.Signed-off-by: Tom Rini
14 Feb, 2018
2 commits
-
Signed-off-by: Tuomas Tynkkynen
-
Signed-off-by: Tuomas Tynkkynen
09 Feb, 2018
1 commit
-
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.Cc: Alexey Brodkin
Cc: Michal Simek
Signed-off-by: Tom Rini
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
05 Feb, 2018
1 commit
-
Probably not all users are aware of this possibility, thus add a
pointer to the README. Also add a useful example.Signed-off-by: Daniel Schwierzeck
12 Jan, 2018
1 commit
-
Add documents to describe NX25 and AE250.
Also update other documents for RISC-V.Signed-off-by: Rick Chen
Signed-off-by: Rick Chen
Signed-off-by: Greentime Hu
27 Dec, 2017
2 commits
-
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.Signed-off-by: Masahiro Yamada
Reviewed-by: York Sun
25 Dec, 2017
1 commit
-
The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabledSo provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"Signed-off-by: Prabhakar Kushwaha
Reviewed-by: York Sun