23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
04 Dec, 2019
1 commit
-
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
22 Nov, 2019
1 commit
-
- Assorted fixes
21 Nov, 2019
3 commits
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
The default mtdparts value grew a trailing zero during the Kconfig
conversion. This is because the mtdparts value in the header file
had a \0 at the end, which got misconverted into plain 0 instead of
being dropped.Signed-off-by: Marek Vasut
Fixes: 43ede0bca7fc ("Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT")
Reviewed-by: Tom Rini -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
08 Nov, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
25 Oct, 2019
1 commit
-
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.Signed-off-by: Frieder Schrempf
Reviewed-by: Stefan Roese
Reviewed-by: Simon Goldschmidt
Acked-by: Lukasz Majewski
Reviewed-by: Heiko Schocher
Reviewed-by: Jagan Teki
07 Oct, 2019
1 commit
-
These boards don't have a watchdog enabled in SPL, so make sure
CONFIG_SPL_WDT is not enabled.Fixes: commit 6874cb72204f ("watchdog: Split WDT from SPL_WDT")
Signed-off-by: Simon Goldschmidt
23 Sep, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
26 Aug, 2019
1 commit
-
This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFSSigned-off-by: Hannes Schmelzer
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini
30 Apr, 2019
1 commit
-
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.Signed-off-by: Simon Goldschmidt
[trini: Re-run migration]
Signed-off-by: Tom Rini
25 Apr, 2019
1 commit
-
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKSOptions implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASEOptions implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDRSigned-off-by: Simon Goldschmidt
Acked-by: Marek Vasut
07 Feb, 2019
1 commit
-
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.Signed-off-by: Vignesh R
Tested-by: Simon Goldschmidt
Tested-by: Stefan Roese
Tested-by: Horatiu Vultur
Reviewed-by: Jagan Teki
Tested-by: Jagan Teki #zynq-microzed
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMACSigned-off-by: Adam Ford
Acked-by: Jagan Teki
Acked-by: Joe Hershberger
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
23 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICESigned-off-by: Adam Ford
04 Jun, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
28 Apr, 2018
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
This converts the following to Kconfig:
CONFIG_SPIThis partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.Signed-off-by: Adam Ford
Signed-off-by: Tom Rini
17 Apr, 2018
3 commits
-
None of the SoCFPGA platforms will support EFI/ISO partition types that
is needed for DISTRO_DEFAULTS. SoCFPGA bootroom will only support 0xa2
partition type.This is needed to help limit the size of the SPL to within the 64k limit
that is required for SoCFPGA.Signed-off-by: Dinh Nguyen
-
Add the DM reset driver to socfpga defconfigs.
Signed-off-by: Dinh Nguyen
-
Enable DM I2C driver on SoCFPGA platforms.
Signed-off-by: Dinh Nguyen
12 Apr, 2018
1 commit
-
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.Signed-off-by: Marek Vasut
Cc: Tom Rini
09 Apr, 2018
1 commit
-
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six
[trini: Re-run migration]
Signed-off-by: Tom Rini
08 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Feb, 2018
1 commit
-
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.Signed-off-by: Tom Rini
11 Feb, 2018
2 commits
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
25 Jan, 2018
1 commit
-
Currently, socfpga_common.h does not allow configurations without
network support. This is because CONFIG_CMD_PXE is defined in this
file and distro mode has DHCP hard-coded as available.Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs
and by making DHCP optional in BOOT_TARGET_DEVICES(func).Signed-off-by: Simon Goldschmidt
09 Jan, 2018
1 commit
-
Enable CONFIG_CMD_PART item, as default environment requires it
and complains this command in unknown.Signed-off-by: Andrey Zhizhikin
06 Nov, 2017
1 commit
-
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.Tested-by: Adam Ford #omap3_logic
Signed-off-by: Tom Rini
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
04 Oct, 2017
1 commit
-
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass
Reviewed-by: Lukasz Majewski
Signed-off-by: Maxime Ripard
28 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
15 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
08 Aug, 2017
1 commit
-
Signed-off-by: Alexandru Gagniuc
Acked-by: Joe Hershberger
26 Jul, 2017
1 commit
-
This converts the following to Kconfig:
CONFIG_FPGA_SOCFPGASigned-off-by: Tien Fong Chee
Reviewed-by: Ley Foon Tan
Reviewed-by: Dinh Nguyen