07 Feb, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Dec, 2019
1 commit
-
This is the first step to use DM support for the KM powerpc boards.
Signed-off-by: Holger Brunck
Reviewed-by: Priyanka Jain
CC: Mario Six
CC: Wolfgang Denk
CC: Valentin Longchamp
CC: Priyanka Jain
04 Dec, 2019
1 commit
-
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
21 Nov, 2019
1 commit
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt
13 Nov, 2019
1 commit
-
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.Signed-off-by: Tom Rini
27 May, 2019
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.Signed-off-by: Tom Rini
21 May, 2019
9 commits
-
Migrate the CONFIG_LCRR_* settings to Kconfig.
Signed-off-by: Mario Six
-
Migrate the arbiter configuration to Kconfig.
Signed-off-by: Mario Six
-
Mirate the HID configuration settings to Kconfig.
Signed-off-by: Mario Six
-
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.Signed-off-by: Mario Six
-
The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.Signed-off-by: Mario Six
-
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.Signed-off-by: Mario Six
-
Migrate the CONFIG_HIGH_BATS variable to Kconfig.
Signed-off-by: Mario Six
-
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.Signed-off-by: Mario Six
-
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config filesSigned-off-by: Mario Six
14 Nov, 2018
1 commit
-
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini
20 Oct, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFISigned-off-by: Adam Ford
[trini: Re-migrate]
Signed-off-by: Tom Rini
18 Aug, 2018
2 commits
-
This converts the following to Kconfig:
CONFIG_MISC_INIT_RSigned-off-by: Adam Ford
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini -
Migrate boards which set bootlimit in the environment to Kconfig.
We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting
if we migrated it.display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME,
but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to
set bootlimit= in display5_factory_defconfig. This is okay because the
display5_factory_defconfig doesn't need to have it set, as it is only
meant to prepare the board in the factory.Environment changes for all modified configs as seen from buildman:
boards.cfg is up to date. Nothing to do.
Summary of 3 commits for 32 boards (8 threads, 1 job per thread)
01: Merge git://git.denx.de/u-boot-x86
arm: + draco etamin rastaban pxm2 display5 thuban rut
02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit
03: Migrate bootlimit to Kconfig
- display5_factory: bootlimit=3Signed-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski
23 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICESigned-off-by: Adam Ford
17 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
09 Apr, 2018
2 commits
-
Migrate the CONFIG_LAST_STAGE_INIT option to Kconfig.
Signed-off-by: Mario Six
-
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.
Signed-off-by: Mario Six
26 Feb, 2018
1 commit
-
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig. In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files. The previous default
only applied in some cases, even on a specific SoC family.Reviewed-by: Lukasz Majewski
Reviewed-by: Alex Kiernan
Signed-off-by: Tom Rini
24 Feb, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIGSigned-off-by: Adam Ford
[trini: Re-run the migration]
Signed-off-by: Tom Rini
15 Feb, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMITSigned-off-by: Lukasz Majewski
Tested-by: Alex Kiernan
Reviewed-by: Hannes Schmelzer
Acked-by: Hannes Schmelzer
11 Feb, 2018
1 commit
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
06 Nov, 2017
1 commit
-
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.Tested-by: Adam Ford #omap3_logic
Signed-off-by: Tom Rini
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
25 Jul, 2017
1 commit
-
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.Signed-off-by: Tom Rini
19 Jun, 2017
1 commit
-
Signed-off-by: Tom Rini
23 May, 2017
2 commits
-
This converts the following to Kconfig:
CONFIG_CMD_JFFS2Signed-off-by: Simon Glass
-
This converts the following to Kconfig:
CONFIG_CMD_IMMAPAlso move this command out of the cmd/ directory since it is
PowerPC-specific.Signed-off-by: Simon Glass
22 May, 2017
1 commit
-
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRINGSigned-off-by: Simon Glass
Reviewed-by: Tom Rini
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini
14 Mar, 2017
1 commit
-
Signed-off-by: Tom Rini
13 Feb, 2017
1 commit
-
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.hSigned-off-by: Masahiro Yamada
30 Dec, 2016
1 commit
-
Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada
Reviewed-by: Jaehoon Chung
28 Oct, 2016
1 commit
-
Add 'PCI' as a menu option and migrate all existing users.
Signed-off-by: Tom Rini
Acked-by: Stephen Warren