Eric Lee / smarc-uboot

23 Jan, 2020

1 commit

21 Jan, 2020

1 commit

16 Jan, 2020

2 commits

  • 14f14911f   arm: mvebu: clearfog: set uboot image SD card offset ... Browse Code »

    Armada 38x ROM skips the first SD card offset when loading SPL. This
    affects the location of the main U-Boot image. SPL MMC code now supports
    U-Boot image offset based on run-time detection of the boot partition.
    Use this feature to make the same generated image support both SD card
    and eMMC boot partition.

    Signed-off-by: Baruch Siach
    Reviewed-by: Stefan Roese
    Signed-off-by: Stefan Roese

    Baruch Siach
     
  • c853fa721   configs: clearfog: enable SPL_DM_GPIO to fix boot from SD ... Browse Code »

    SPL needs DM GPIO to read the SD card-detect signal. This complements
    the fix in commit 70bae02f71d4 ("arm: mvebu: clearfog: fix boot from SD
    card").

    Signed-off-by: Baruch Siach
    Reviewed-by: Stefan Roese
    Signed-off-by: Stefan Roese

    Baruch Siach
     

05 Dec, 2019

2 commits

21 Nov, 2019

1 commit

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     

08 Nov, 2019

1 commit

23 Sep, 2019

1 commit

26 Aug, 2019

1 commit

02 Aug, 2019

1 commit

  • 37304aaf6   Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig ... Browse Code »
    4

    This converts the following to Kconfig:
    CONFIG_USE_PREBOOT
    CONFIG_PREBOOT

    Both are together in one commit, since otherwise the former causes kconfig
    to define the latter, which gives duplicate symbol errors.

    Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
    backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

    Signed-off-by: Simon Glass

    Simon Glass
     

27 May, 2019

1 commit

09 May, 2019

1 commit

  • 170aca203   arm: mvebu: clearfog: Enable BLK and DM support ... Browse Code »

    This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
    to remove these compile warnings:

    ===================== WARNING ======================
    This board does not use CONFIG_DM_MMC. Please update
    the board to use CONFIG_DM_MMC before the v2019.04 release.
    Failure to update by the deadline may result in board removal.
    See doc/driver-model/MIGRATION.txt for more info.
    ====================================================
    ===================== WARNING ======================
    This board does not use CONFIG_DM_USB. Please update
    the board to use CONFIG_DM_USB before the v2019.07 release.
    Failure to update by the deadline may result in board removal.
    See doc/driver-model/MIGRATION.txt for more info.
    ====================================================
    ===================== WARNING ======================
    This board does use CONFIG_LIBATA but has CONFIG_AHCI not
    enabled. Please update the storage controller driver to use
    CONFIG_AHCI before the v2019.07 release.
    Failure to update by the deadline may result in board removal.
    See doc/driver-model/MIGRATION.txt for more info.
    ====================================================

    Signed-off-by: Stefan Roese

    Stefan Roese
     

05 May, 2019

1 commit

  • 623de3f08   Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_SUPPORT_EMMC_BOOT

    As requested by Michal Simek , these boards
    have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

    xilinx_zynqmp_zc1275_revB
    xilinx_zynqmp_zc1751_xm018_dc4
    xilinx_zynqmp_zc1751_xm019_dc5
    xilinx_zynqmp_zcu100_revC
    xilinx_zynqmp_zcu102_rev1_0
    xilinx_zynqmp_zcu102_revA
    xilinx_zynqmp_zcu102_revB
    xilinx_zynqmp_zcu104_revA
    xilinx_zynqmp_zcu104_revC
    xilinx_zynqmp_zcu106_revA
    xilinx_zynqmp_zcu111_revA

    Signed-off-by: Alex Kiernan
    Acked-by: Lukasz Majewski
    Acked-by: Patrick Delaunay
    Acked-by: Ramon Fried
    Reviewed-by: Andy Shevchenko
    Tested-by: Sébastien Szymanski

    Alex Kiernan
     

30 Apr, 2019

2 commits

26 Mar, 2019

1 commit

  • 14453fbfa   Convert CONFIG_SF_DEFAULT_* to Kconfig ... Browse Code »
    36

    This converts the following to Kconfig:
    CONFIG_SF_DEFAULT_BUS
    CONFIG_SF_DEFAULT_CS
    CONFIG_SF_DEFAULT_MODE
    CONFIG_SF_DEFAULT_SPEED

    I use moveconfig script and then manual check on generated u-boot.cfg
    to solve the remaining issue.

    Signed-off-by: Patrick Delaunay

    Patrick Delaunay
     

08 Feb, 2019

1 commit

07 Feb, 2019

1 commit

  • 6d8251783   configs: Don't use SPI_FLASH_BAR as default ... Browse Code »
    12

    Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
    don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
    4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
    renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
    not break functionality.

    Signed-off-by: Vignesh R
    Tested-by: Simon Goldschmidt
    Tested-by: Stefan Roese
    Tested-by: Horatiu Vultur
    Reviewed-by: Jagan Teki
    Tested-by: Jagan Teki #zynq-microzed

    Vignesh R
     

05 Feb, 2019

1 commit

  • 94f453ea3   pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfig ... Browse Code »

    This patch adds DM_PCI support to the MVEBU PCIe driver. This is
    necessary, since all PCI drivers have to be moved to DM (driver model)
    until the v2019.07 release.

    To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
    from config headers to the defconfig files.

    Signed-off-by: Stefan Roese
    Cc: Dirk Eibach
    Cc: Mario Six
    Cc: Chris Packham
    Cc: Phil Sutter
    Cc: Marek Behún
    Cc: VlaoMao

    Stefan Roese
     

08 Jan, 2019

1 commit

17 Nov, 2018

1 commit

04 Sep, 2018

1 commit

18 Aug, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

06 Aug, 2018

1 commit

  • ca1a4c863   mvebu: select boot device at SoC level ... Browse Code »
    1

    Move the gdsys Controlcenter DC specific build time kwbimage.cfg
    generation code into the mach-mvebu/ directory to be shared by all 32bit
    mvebu platforms.

    Remove board specific kwbimage.cfg files, and use the generated one
    instead. These files are all identical, with two exceptions. Clearfog
    and Helios4 use the sdio boot device, whereas all others use spi. Update
    the defconfigs for the exceptional boards to generate the same
    kwbimage.cfg as before.

    Signed-off-by: Baruch Siach
    Signed-off-by: Stefan Roese

    Baruch Siach
     

05 Jun, 2018

2 commits

04 Jun, 2018

1 commit

15 May, 2018

1 commit

09 Apr, 2018

1 commit

08 Apr, 2018

1 commit

30 Mar, 2018

1 commit

14 Feb, 2018

1 commit

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

19 Dec, 2017

1 commit

16 Nov, 2017

2 commits

  • 962b8fef9   arm: mvebu: clearfog: Fix SPI-NOR flash access ... Browse Code »

    The production variant of the SPI flash used by the clearfog
    devices are based on winbond chips. Additionally enable
    SPI_FLASH_BAR since some variants will have 16MB of flash
    that requires this to be enabled.

    Remove the default speed and mode; these values are taken from the
    device tree when CONFIG_DM_SPI_FLASH is enabled.

    Add default bus, so that 'sf' detects the SPI flash by default.

    Signed-off-by: Jon Nettleton
    [baruch: remove speed/mode; add bus; move winbond to defconfig]
    Signed-off-by: Baruch Siach
    Signed-off-by: Stefan Roese

    Jon Nettleton
     
  • b4b06ac6f   arm: mvebu: clearfog: enable XHCI USB ... Browse Code »

    Enable the driver by default for the clearfog boards since the external
    port is configured for XHCI.

    Signed-off-by: Jon Nettleton
    [baruch: split from the SoC setup patch]
    Signed-off-by: Baruch Siach
    Signed-off-by: Stefan Roese

    Jon Nettleton
     

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

26 Sep, 2017

1 commit