28 Apr, 2014
33 commits
-
This patch fixes this section mismatch:
WARNING: vmlinux.o(.text+0x1efc4): Section mismatch in reference from
the function apm821xx_pciex_init_port_hw() to the function
.init.text:ppc4xx_pciex_wait_on_sdr.isra.9()The function apm821xx_pciex_init_port_hw() references the function
__init ppc4xx_pciex_wait_on_sdr.isra.9(). This is often because
apm821xx_pciex_init_port_hw lacks a __init annotation or the
annotation of ppc4xx_pciex_wait_on_sdr.isra.9 is wrong.apm821xx_pciex_init_port_hw is only referenced by a struct in
__initdata, so it should be safe to add __init to
apm821xx_pciex_init_port_hw.Signed-off-by: Alistair Popple
Signed-off-by: Benjamin Herrenschmidt -
When the guest cedes the vcpu or the vcpu has no guest to
run it naps. Clear the runlatch bit of the vcpu before
napping to indicate an idle cpu.Signed-off-by: Preeti U Murthy
Acked-by: Paul Mackerras
Reviewed-by: Srivatsa S. Bhat
Signed-off-by: Benjamin Herrenschmidt -
The secondary threads in the core are kept offline before launching guests
in kvm on powerpc: "371fefd6f2dc4666:KVM: PPC: Allow book3s_hv guests to use
SMT processor modes."Hence their runlatch bits are cleared. When the secondary threads are called
in to start a guest, their runlatch bits need to be set to indicate that they
are busy. The primary thread has its runlatch bit set though, but there is no
harm in setting this bit once again. Hence set the runlatch bit for all
threads before they start guest.Signed-off-by: Preeti U Murthy
Acked-by: Paul Mackerras
Reviewed-by: Srivatsa S. Bhat
Signed-off-by: Benjamin Herrenschmidt -
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.Signed-off-by: Preeti U Murthy
Acked-by: Paul Mackerras
Reviewed-by: Srivatsa S. Bhat
Signed-off-by: Benjamin Herrenschmidt -
While testing memory hot-remove, I found following dead lock:
Process #1141 is drmgr, trying to remove some memory, i.e. memory499.
It holds the memory_hotplug_mutex, and blocks when trying to remove file
"online" under dir memory499, in kernfs_drain(), at
wait_event(root->deactivate_waitq,
atomic_read(&kn->active) == KN_DEACTIVATED_BIAS);Process #1120 is trying to online memory499 by
echo 1 > memory499/onlineIn .kernfs_fop_write, it uses kernfs_get_active() to increase
&kn->active, thus blocking process #1141. While itself is blocked later
when trying to acquire memory_hotplug_mutex, which is held by processThe backtrace of both processes are shown below:
[] 0xc000000001b18600
[] .__switch_to+0x144/0x200
[] .online_pages+0x74/0x7b0
[] .memory_subsys_online+0x9c/0x150
[] .device_online+0xb8/0x120
[] .online_store+0xb4/0xc0
[] .dev_attr_store+0x64/0xa0
[] .sysfs_kf_write+0x7c/0xb0
[] .kernfs_fop_write+0x154/0x1e0
[] .vfs_write+0xe0/0x260
[] .SyS_write+0x64/0x110
[] syscall_exit+0x0/0x7c[] 0xc000000001b18600
[] .__switch_to+0x144/0x200
[] .__kernfs_remove+0x204/0x300
[] .kernfs_remove_by_name_ns+0x68/0xf0
[] .sysfs_remove_file_ns+0x38/0x60
[] .device_remove_attrs+0x54/0xc0
[] .device_del+0x158/0x250
[] .device_unregister+0x34/0xa0
[] .unregister_memory_section+0x164/0x170
[] .__remove_pages+0x108/0x4c0
[] .arch_remove_memory+0x60/0xc0
[] .remove_memory+0x8c/0xe0
[] .pseries_remove_memblock+0xd4/0x160
[] .pseries_memory_notifier+0x27c/0x290
[] .notifier_call_chain+0x8c/0x100
[] .__blocking_notifier_call_chain+0x6c/0xe0
[] .of_property_notify+0x7c/0xc0
[] .of_update_property+0x3c/0x1b0
[] .ofdt_write+0x3dc/0x740
[] .proc_reg_write+0xac/0x110
[] .vfs_write+0xe0/0x260
[] .SyS_write+0x64/0x110
[] syscall_exit+0x0/0x7cThis patch uses lock_device_hotplug() to protect remove_memory() called
in pseries_remove_memblock(), which is also stated before function
remove_memory():* NOTE: The caller must call lock_device_hotplug() to serialize hotplug
* and online/offline operations before this call, as required by
* try_offline_node().
*/
void __ref remove_memory(int nid, u64 start, u64 size)With this lock held, the other process(#1120 above) trying to online the
memory block will retry the system call when calling
lock_device_hotplug_sysfs(), and finally find No such device error.Signed-off-by: Li Zhong
Signed-off-by: Benjamin Herrenschmidt -
module_init should return 0 or a negative errno.
Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
Bump the boot wrapper BOOT_COMMAND_LINE_SIZE to match the
kernel.Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
I've had a report that the current limit is too small for
an automated network based installer. Bump it.Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
We have two definitions of COMMAND_LINE_SIZE, one for the kernel
and one for the boot wrapper. I assume this is so the boot
wrapper can be self sufficient and not rely on kernel headers.Having two defines with the same name is confusing, I just
updated the wrong one when trying to bump it.Make the boot wrapper define unique by calling it
BOOT_COMMAND_LINE_SIZE.Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
The catalog version number was changed from a be32 (with proceeding
32bits of padding) to a be64, update the code to treat it as a be64Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
fixup for "powerpc/perf: Add support for the hv gpci (get performance
counter info) interface".Makes the "not enabled" message less awful (and hidden unless
debugging).Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
fixup for "powerpc/perf: Add support for the hv 24x7 interface"
Makes the "not enabled" message less awful (and hides it in most cases).
Signed-off-by: Cody P Schafer
Signed-off-by: Benjamin Herrenschmidt -
The if condition check was based on a draft ISA doc. Remove the same.
Signed-off-by: Aneesh Kumar K.V
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard
Reviewed-by: Stewart Smith
Signed-off-by: Benjamin Herrenschmidt -
The bitmap in opal_poll_events and opal_handle_interrupt is
big endian, so we need to byteswap it on little endian builds.Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
We had some duplication of the internal OPAL functions.
Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.Signed-off-by: Anton Blanchard
Reviewed-by: Stewart Smith
Signed-off-by: Benjamin Herrenschmidt -
On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.This patch release the unnecessary refcount.
Signed-off-by: Wei Yang
Signed-off-by: Benjamin Herrenschmidt -
During the EEH hotplug event, iommu_add_device() will be invoked three times
and two of them will trigger warning or error.The three times to invoke the iommu_add_device() are:
pci_device_add
...
set_iommu_table_base_and_group kobj->sd is not initialized. The
dev->kobj->sd is initialized in device_add().
The third time's warning is triggered by the re-attach of the iommu_group.After applying this patch, the error
iommu_tce: 0003:05:00.0 has not been added, ret=-14
and the warning
[ 204.123609] ------------[ cut here ]------------
[ 204.123645] WARNING: at arch/powerpc/kernel/iommu.c:1125
[ 204.123680] Modules linked in: xt_CHECKSUM nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT bnep bluetooth 6lowpan_iphc rfkill xt_conntrack ebtable_nat ebtable_broute bridge stp llc mlx4_ib ib_sa ib_mad ib_core ib_addr ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw bnx2x tg3 mlx4_core nfsd ptp mdio ses libcrc32c nfs_acl enclosure be2net pps_core shpchp lockd kvm uinput sunrpc binfmt_misc lpfc scsi_transport_fc ipr scsi_tgt
[ 204.124356] CPU: 18 PID: 650 Comm: eehd Not tainted 3.14.0-rc5yw+ #102
[ 204.124400] task: c0000027ed485670 ti: c0000027ed50c000 task.ti: c0000027ed50c000
[ 204.124453] NIP: c00000000003cf80 LR: c00000000006c648 CTR: c00000000006c5c0
[ 204.124506] REGS: c0000027ed50f440 TRAP: 0700 Not tainted (3.14.0-rc5yw+)
[ 204.124558] MSR: 9000000000029032 CR: 88008084 XER: 20000000
[ 204.124682] CFAR: c00000000006c644 SOFTE: 1
GPR00: c00000000006c648 c0000027ed50f6c0 c000000001398380 c0000027ec260300
GPR04: c0000027ea92c000 c00000000006ad00 c0000000016e41b0 0000000000000110
GPR08: c0000000012cd4c0 0000000000000001 c0000027ec2602ff 0000000000000062
GPR12: 0000000028008084 c00000000fdca200 c0000000000d1d90 c0000027ec281a80
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
GPR24: 000000005342697b 0000000000002906 c000001fe6ac9800 c000001fe6ac9800
GPR28: 0000000000000000 c0000000016e3a80 c0000027ea92c090 c0000027ea92c000
[ 204.125353] NIP [c00000000003cf80] .iommu_add_device+0x30/0x1f0
[ 204.125399] LR [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
[ 204.125443] Call Trace:
[ 204.125464] [c0000027ed50f6c0] [c0000027ed50f750] 0xc0000027ed50f750 (unreliable)
[ 204.125526] [c0000027ed50f750] [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
[ 204.125588] [c0000027ed50f7d0] [c000000000069cc8] .pnv_pci_dma_dev_setup+0x78/0x340
[ 204.125650] [c0000027ed50f870] [c000000000044408] .pcibios_setup_device+0x88/0x2f0
[ 204.125712] [c0000027ed50f940] [c000000000046040] .pcibios_setup_bus_devices+0x60/0xd0
[ 204.125774] [c0000027ed50f9c0] [c000000000043acc] .pcibios_add_pci_devices+0xdc/0x1c0
[ 204.125837] [c0000027ed50fa50] [c00000000086f970] .eeh_reset_device+0x36c/0x4f0
[ 204.125939] [c0000027ed50fb20] [c00000000003a2d8] .eeh_handle_normal_event+0x448/0x480
[ 204.126068] [c0000027ed50fbc0] [c00000000003a35c] .eeh_handle_event+0x4c/0x340
[ 204.126192] [c0000027ed50fc80] [c00000000003a74c] .eeh_event_handler+0xfc/0x1b0
[ 204.126319] [c0000027ed50fd30] [c0000000000d1ea0] .kthread+0x110/0x130
[ 204.126430] [c0000027ed50fe30] [c00000000000a460] .ret_from_kernel_thread+0x5c/0x7c
[ 204.126556] Instruction dump:
[ 204.126610] 7c0802a6 fba1ffe8 fbc1fff0 fbe1fff8 f8010010 f821ff71 7c7e1b78 60000000
[ 204.126787] 60000000 e87e0298 3143ffff 7d2a1910 2fa90000 40de00c8 ebfe0218
[ 204.126966] ---[ end trace 6e7aefd80add2973 ]---are cleared.
This patch removes iommu_add_device() in pnv_pci_ioda_dma_dev_setup(), which
revert part of the change in commit d905c5df(PPC: POWERNV: move
iommu_add_device earlier).Signed-off-by: Wei Yang
Signed-off-by: Benjamin Herrenschmidt -
With this patch I was able to update firmware on an LE kernel.
Signed-off-by: Anton Blanchard
Signed-off-by: Benjamin Herrenschmidt -
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.Signed-off-by: Benjamin Herrenschmidt
-
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.Signed-off-by: Joel Stanley
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Benjamin Herrenschmidt
-
The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: Benjamin Herrenschmidt
-
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.Signed-off-by: Joel Stanley
Signed-off-by: Benjamin Herrenschmidt -
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.Signed-off-by: Joel Stanley
Signed-off-by: Benjamin Herrenschmidt -
commit 41dd03a9 may cause Oops in rtas_stop_self().
The reason is that the rtas_args was moved into stack space. For a box
with more that 4GB RAM, the stack could easily be outside 32bit range,
but RTAS is 32bit.So the patch moves rtas_args away from stack by adding static before
it.Signed-off-by: Li Zhong
Signed-off-by: Anton Blanchard
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt -
Commit aac416fc38c (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.Signed-off-by: Jeff Mahoney
Signed-off-by: Benjamin Herrenschmidt
19 Apr, 2014
1 commit
-
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
...
Building modules, stage 2.
WARNING: 1 bad relocations
c0000000013d6a30 R_PPC64_ADDR64 uprobes_fetch_type_table
WRAP arch/powerpc/boot/zImage.pseries
WRAP arch/powerpc/boot/zImage.epapr
MODPOST 1849 modules
ERROR: ".__node_distance" [drivers/block/nvme.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....The reason is symbol "__node_distance" not been exported in powerpc.
Signed-off-by: Mike Qiu
Acked-by: Benjamin Herrenschmidt
Cc: Paul Mackerras
Cc: Nathan Fontenot
Cc: Stephen Rothwell
Cc: Srivatsa S. Bhat
Cc: Jesse Larrew
Cc: Robert Jennings
Cc: Alistair Popple
Cc: Mike Qiu
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds
15 Apr, 2014
1 commit
-
3bc955987fb3 ("powerpc/PCI: Use list_for_each_entry() for bus traversal")
caused a NULL pointer dereference because the loop body set the iterator to
NULL:Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000041d78
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041d78] .sys_pciconfig_iobase+0x68/0x1f0
LR [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0
Call Trace:
[c0000003b4787db0] [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0 (unreliable)
[c0000003b4787e30] [c000000000009ed8] syscall_exit+0x0/0x98Fix it by using a temporary variable for the iterator.
[bhelgaas: changelog, drop tmp_bus initialization]
Fixes: 3bc955987fb3 powerpc/PCI: Use list_for_each_entry() for bus traversal
Signed-off-by: Mike Qiu
Signed-off-by: Bjorn Helgaas
13 Apr, 2014
3 commits
-
Commit 8f619b5429d9 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode. The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic. The visible result is that
the kernel hangs after printing "returning from prom_init".This fixes it by checking for hypervisor mode being available before
setting LPCR. If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.Signed-off-by: Paul Mackerras
Acked-by: Benjamin Herrenschmidt
Signed-off-by: Linus Torvalds -
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
... -
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
12 Apr, 2014
1 commit
-
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
09 Apr, 2014
1 commit
-
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...