01 Apr, 2015
1 commit
-
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.Signed-off-by: Bo Shen
12 Jun, 2014
1 commit
-
This prevents some warnings when building with clang.
cc:: andreas.devel@googlemail.com
Signed-off-by: Jeroen Hofstee
27 May, 2014
1 commit
-
Also we enable the mmc command in configuration file.
As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.Signed-off-by: Josh Wu
Signed-off-by: Andreas Bießmann
02 Dec, 2013
1 commit
-
add common phy reset code into a common function.
Signed-off-by: Heiko Schocher
Cc: Andreas Bießmann
Cc: Bo Shen
Cc: Jens Scharsig
Cc: Sergey Lapin
Cc: Stelian Pop
Cc: Albin Tonnerre
Cc: Eric Benard
Cc: Markus Hubig
Acked-by: Jens Scharsig (BuS Elektronik)
Tested-by: Jens Scharsig (BuS Elektronik)
Tested-by: Bo Shen
Acked-by: Bo Shen
Signed-off-by: Andreas Bießmann
24 Jul, 2013
1 commit
-
Signed-off-by: Wolfgang Denk
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini
01 Sep, 2012
1 commit
-
A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.Signed-off-by: Andreas Bießmann
cc: Jens Scharsig
cc: Stelian Pop
cc: Sedji Gaouaou
cc: Albin Tonnerre
cc: Eric Benard
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: Jens Scharsig (BuS Elektronik)
Tested-by: Jens Scharsig (BuS Elektronik)
29 Nov, 2011
1 commit
-
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop
Signed-off-by: Anatolij Gustschin
04 Sep, 2011
1 commit
-
Based on earlier work by Alex Waterman .
Signed-off-by: Thomas Petazzoni
12 Jul, 2010
1 commit
-
Also, remove all calls to eth_init() in boards that use MACB
Signed-off-by: Ben Warren
01 Jul, 2010
1 commit
-
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.Signed-off-by: Sergey Matyukevich
08 Mar, 2010
1 commit
-
Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCKSigned-off-by: Achim Ehrlich
12 Jul, 2009
1 commit
-
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.Signed-off-by: Sedji Gaouaou