26 Mar, 2019
1 commit
-
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEEDI use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.Signed-off-by: Patrick Delaunay
22 Mar, 2019
1 commit
-
With U-boot supporting environment in multiple places, enable only
ENV_IS_IN_EMMCSigned-off-by: Faiz Abbas
Reviewed-by: Lokesh Vutla
Reviewed-by: Tom Rini
07 Feb, 2019
1 commit
-
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.Signed-off-by: Vignesh R
Tested-by: Simon Goldschmidt
Tested-by: Stefan Roese
Tested-by: Horatiu Vultur
Reviewed-by: Jagan Teki
Tested-by: Jagan Teki #zynq-microzed
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
10 Dec, 2018
3 commits
-
- DM_I2C_COMPAT removal for all ti platforms from Jean-Jacques Hiblot
- Fix in i2c command help output from Chirstoph Muellner. -
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini
Reviewed-by: Heiko Schocher -
This is required to take advantage of MULTI_DTB_FIT before relocation.
If it is too low, DM will be initialized only after relocation has
taken place. That is too late for the DRA7 because I2C DM is used before
the relocation to setup the voltages required, among other things, to
properly initialize the DRAM.Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini
Reviewed-by: Heiko Schocher
07 Dec, 2018
1 commit
-
Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini
14 Nov, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
2 commits
-
This converts the following to Kconfig:
CONFIG_MISC_INIT_RSigned-off-by: Adam Ford
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini -
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMACSigned-off-by: Adam Ford
Acked-by: Jagan Teki
Acked-by: Joe Hershberger
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
04 Jun, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
30 May, 2018
2 commits
-
Convert USB fastboot code to use shared fastboot protocol.
Signed-off-by: Alex Kiernan
Reviewed-by: Simon Glass -
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.Signed-off-by: Alex Kiernan
Reviewed-by: Simon Glass
Acked-by: Joe Hershberger
28 Apr, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_SPIThis partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.Signed-off-by: Adam Ford
Signed-off-by: Tom Rini
14 Apr, 2018
1 commit
-
Those options are required to enable support for SATA on DRA7 platforms.
Signed-off-by: Jean-Jacques Hiblot
12 Apr, 2018
1 commit
-
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.Signed-off-by: Marek Vasut
Cc: Tom Rini
09 Apr, 2018
2 commits
-
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan
Reviewed-by: Lukasz Majewski
Reviewed-by: Petr Vorel
Reviewed-by: Petr Vorel -
This converts CONFIG_DRIVER_TI_CPSW to Kconfig
Signed-off-by: Alex Kiernan
Acked-by: Joe Hershberger
08 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
14 Mar, 2018
1 commit
-
Beside enabling the support for HS200 in mmc core, enabling the HS200
support in the SPL requires multi-dtb support in the SPL because pinctrl
and IOdelays vary across SOCs.Also we need to make sure that the pinctrl properties arenot removed from
the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and
interrupts properties.Signed-off-by: Jean-Jacques Hiblot
23 Feb, 2018
1 commit
-
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.Signed-off-by: Tom Rini
19 Feb, 2018
1 commit
-
By default UHS and HS200 are not enabled.
Signed-off-by: Jean-Jacques Hiblot
23 Jan, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_OMAP_USB_PHYSigned-off-by: Adam Ford
17 Oct, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
04 Oct, 2017
2 commits
-
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.That will also reduce the boilerplate in the defconfigs.
Reviewed-by: Łukasz Majewski
Reviewed-by: Simon Glass
Signed-off-by: Maxime Ripard -
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass
Reviewed-by: Lukasz Majewski
Signed-off-by: Maxime Ripard
30 Sep, 2017
1 commit
-
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it. select this and re-sync the defconfigs.Signed-off-by: Tom Rini
12 Sep, 2017
1 commit
-
Add support for selecting proper dtb for
dra76x u-boot from FIT.Signed-off-by: Lokesh Vutla
Reviewed-by: Tom Rini
02 Sep, 2017
1 commit
-
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the READMESigned-off-by: Tom Rini
28 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
27 Aug, 2017
1 commit
-
Signed-off-by: Sam Protsenko
12 Aug, 2017
1 commit
-
This converts the following to Kconfig:
CONFIG_CMD_SPLNote that trats does not actually use SPL, so this option can no-longer be
set.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng
Reviewed-by: Philipp Tomsich
11 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
09 Aug, 2017
1 commit
-
Reviewed-by: Joe Hershberger
Signed-off-by: Tom Rini
08 Aug, 2017
1 commit
-
Signed-off-by: Alexandru Gagniuc
Acked-by: Joe Hershberger
01 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini