16 Jun, 2020
2 commits
-
Update board codes and DTS files to add display relevant nodes and
configurations.
Support two video links with MIPI DSI:
1. MIPI DSI to HDMI convertor, this is default
2. RM67191 panelSigned-off-by: Ye Li
(cherry picked from commit e14979fc1798a933be643b4f52d2bfca5df1e552) -
enable CONFIG_OF_LIBFDT_OVERLAY. It can be used by u-boot
to apply a dto built by OP-TEE.Signed-off-by: Silvano di Ninno
Reviewed-by: Ye Li
(cherry picked from commit 077f8afa2bf07c42cc3e3c3875f63dba49231443)
06 May, 2020
4 commits
-
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.When OPTEE memory is removed from first bank, it may split the first bank
to two banks, so increase the CONFIG_NR_DRAM_BANKS and adjust the MMU
table for the split case.Signed-off-by: Ye Li
Signed-off-by: Silvano di Ninno
Tested-by: Silvano di Ninno
(cherry picked from commit e2a3b770ef847354ebe85c363608f27381d48adc) -
If inline ECC is enabled on imx8mp, then the ECC region should be
reserved. Since the limit of the ddr address map when use inline ecc
and 6G memory, ECC region have to be divided into three parts. So these
three parts ECC region should be set as reserved-memory with no-map.Signed-off-by: Sherry Sun
(cherry picked from commit 0ea77fc9364e46e897cfa554d93895595aaf2a20) -
Change the SPL to non-DM and enable USB/tcpc, TMU, flexspi, FEC
and eQOS.Signed-off-by: Ye Li
-
Print out atf commit in U-Boot.
Signed-off-by: Peng Fan
(cherry picked from commit df89948806c38e38119767a67ef0e18f24ac886b)
(cherry picked from commit 3a17aa1659fbfe675b74ada60a481d93bb557cdc)
(cherry picked from commit 60780b360889a4366159d342dd7e197faf0d1ca2)
23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
08 Jan, 2020
1 commit
-
Add basic i.MX8MP EVK board support
U-Boot SPL 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)
power_pca9450b_init
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Failed to find clock node. Check device tree
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0U-Boot 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)
CPU: Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM: 6 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2Signed-off-by: Peng Fan