23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
05 Dec, 2019
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
21 Nov, 2019
2 commits
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
08 Nov, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
02 Sep, 2019
1 commit
-
- r8a66597 usb changes
26 Aug, 2019
3 commits
-
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.Signed-off-by: Stefan Roese
Cc: Eugen Hristev
Cc: Miquel Raynal
Cc: Gregory CLEMENT
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini -
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INITSigned-off-by: Adam Ford
Acked-by: Chris Packham
Tested-by: Felix Brack -
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Aug, 2019
1 commit
-
Enable USB host support on GR Peach board.
To use USB host on GR Peach, it might be necessary to solder JP3 header
onto the board first and then short it. Shorting JP3 is mandatory to let
the U5 regulator to supply VBUS to the CN3 USB port.Signed-off-by: Marek Vasut
Cc: Chris Brandt
07 May, 2019
1 commit
-
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.Signed-off-by: Marek Vasut
Cc: Chris Brandt
Cc: Nobuhiro Iwamatsu
