29 Feb, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
05 Dec, 2019
3 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
MTD support must be enabled when using mtdparts. Indeed, functions
like get_mtd_info(), get_mtd_device() and put_mtd_device() are in
drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon -
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini
04 Dec, 2019
1 commit
-
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini
Reviewed-by: Boris Brezillon
21 Nov, 2019
3 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
13 Nov, 2019
1 commit
-
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.Signed-off-by: Tom Rini
08 Nov, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
26 Aug, 2019
3 commits
-
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.Signed-off-by: Stefan Roese
Cc: Eugen Hristev
Cc: Miquel Raynal
Cc: Gregory CLEMENT
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini -
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INITSigned-off-by: Adam Ford
Acked-by: Chris Packham
Tested-by: Felix Brack -
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
14 Aug, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
09 Jul, 2019
1 commit
-
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"Signed-off-by: Markus Klotzbuecher
Cc: Heiko Schocher
Cc: Eugen Hristev
Cc: Tom Rini
27 May, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 May, 2019
1 commit
-
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.Acked-by: Alexey Brodkin
Signed-off-by: Trevor Woerner
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini
03 May, 2019
1 commit
-
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.Signed-off-by: Heiko Schocher
30 Apr, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
09 Apr, 2019
1 commit
-
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.Signed-off-by: Stefan Roese
Cc: Heiko Schocher
Cc: Andreas Bießmann
Cc: Eugen Hristev
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
17 Nov, 2018
1 commit
-
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.Signed-off-by: Prasanthi Chellakumar
14 Nov, 2018
1 commit
-
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
08 Aug, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICESigned-off-by: Adam Ford
22 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_NAND_ATMELSigned-off-by: Adam Ford
04 Jun, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
12 Apr, 2018
1 commit
-
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.Signed-off-by: Marek Vasut
Cc: Tom Rini
08 Apr, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
11 Feb, 2018
1 commit
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
06 Feb, 2018
1 commit
-
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endifwhich means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
04 Oct, 2017
1 commit
-
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass
Reviewed-by: Lukasz Majewski
Signed-off-by: Maxime Ripard
28 Aug, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
20 Aug, 2017
1 commit
-
since commit: b529993e0222 "spl: add hierarchical defaults for SPL_LDSCRIPT"
taurus board stopped working. Use the ldscript from
arch/arm/cpu/u-boot-spl.lds (as before this patch) fixed it.Signed-off-by: Heiko Schocher
Reviewed-by: Philipp Tomsich
15 Aug, 2017
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.Signed-off-by: Sam Protsenko
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini
08 Aug, 2017
1 commit
-
Signed-off-by: Alexandru Gagniuc
Acked-by: Joe Hershberger