18 Nov, 2013
1 commit
-
Signed-off-by: Masahiro Yamada
01 Nov, 2013
1 commit
-
Signed-off-by: Masahiro Yamada
Cc: Albert ARIBAUD
Cc: Andreas Bießmann
Cc: Stefano Babic
Cc: Prafulla Wadaskar
Cc: Minkyu Kang
Cc: Vipin Kumar
Cc: Tom Warren
Cc: Tom Rini
19 Aug, 2013
1 commit
-
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.hSigned-off-by: Tom Rini
10 Aug, 2013
2 commits
-
to use this driver also on am335x based boards, the following
changes are made:- struct lcd_ctrl_config lcd_cfg is now configurable
through board code- controller base is configurable through define
DA8XX_LCD_CNTL_BASE. To be compatible with older
da8xx based boards: If this define is missing, the
DAVINCI_LCD_CNTL_BASE is used- Determine LCD IP Version, and make the driver
working on lcd revision register values:
Version 1:
0x4C100102
Version 2:
0x4F200800
0x4F201000Signed-off-by: Heiko Schocher
Cc: Stefano Babic
Cc: Anatolij Gustschin
Cc: Tom Rini
Acked-by: Tom Rini -
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.Signed-off-by: Heiko Schocher
Cc: Stefano Babic
Cc: Anatolij Gustschin
Cc: Tom Rini
Acked-by: Tom Rini
27 Jul, 2013
1 commit
-
The current code uses clrbits_be32 which is incorrect since we are on
a little endian machine here. This patch fixes this issue and also removes
some unnecessary code: Reading the current GPIO bank state is not required
if we are using the SET and CLEAR GPIO registers for setting/clearing
bits.Signed-off-by: Christian Riesch
Cc: Nagabhushana Netagunte
Cc: Rajashekhara, Sudhakar
24 Jul, 2013
1 commit
-
Signed-off-by: Wolfgang Denk
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini
22 Jun, 2013
1 commit
-
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebaseNote: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.Signed-off-by: Albert ARIBAUD
Tested-by: Lubomir Popov
Tested-by: Jeroen Hofstee
Reviewed-by: Benoît Thébaudeau
10 Jun, 2013
2 commits
-
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.Signed-off-by: Vishwanathrao Badarkhe, Manish
Reviewed-by: Tom Rini
Acked-by: Christian Riesch -
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).Signed-off-by: Vishwanathrao Badarkhe, Manish
14 Apr, 2013
1 commit
-
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.Signed-off-by: Albert ARIBAUD
12 Apr, 2013
2 commits
-
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.Signed-off-by: Benoît Thébaudeau
-
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).Signed-off-by: Benoît Thébaudeau
19 Mar, 2013
1 commit
-
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.hBuild tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini
16 Mar, 2013
1 commit
-
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.Signed-off-by: Simon Glass
13 Mar, 2013
1 commit
-
Many SPL linker scripts needlessly include linker lists (aka LGAs).
Remove them whenever possible; keep it only in the seven am335x_evm
variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot),
where there is actual content in output section .u_boot_list.This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets
byte-identical.Signed-off-by: Albert ARIBAUD
22 Oct, 2012
1 commit
-
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.Signed-off-by: Marek Vasut
Cc: Joe Hershberger
Cc: Mike Frysinger
02 Oct, 2012
2 commits
-
Do not allow to overwrite it when video is enabled.
Signed-off-by: Bastian Ruppert
CC: Tom Rini
Acked-by: Stefano Babic -
Signed-off-by: Bastian Ruppert
CC: Tom Rini
Acked-by: Stefano Babic
28 Sep, 2012
1 commit
-
This file documents when to build for da850evm and when to build for
da850_am18xxevm. It also documents how to write the u-boot.ais file to
persistent storage (such as SPI), in some cases as well as how to write
a recovery image.Signed-off-by: Tom Rini
Acked-by: Christian Riesch
Acked-by: Prabhakar Lad
01 Sep, 2012
5 commits
-
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu
-
Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x08222204, where as currently it
configured to 0x00100084 in U-Boot. This issue was found out when
support for NAND SPL is added in U-Boot. Without this patch U-Boot
does not come up with SPL.Tested-by: Christian Riesch
Signed-off-by: Lad, Prabhakar
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Hadli, Manjunath -
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.Tested-by: Christian Riesch
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Lad, Prabhakar
Signed-off-by: Hadli, Manjunath -
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch
Signed-off-by: Lad, Prabhakar
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Hadli, Manjunath -
Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.Signed-off-by: Sughosh Ganu
29 Jul, 2012
1 commit
-
Also drop a few files referring to no longer / not yet supported
boards.Signed-off-by: Wolfgang Denk
Cc: Prafulla Wadaskar
Cc: Stefan Roese
Cc: Kim Phillips
Cc: Andy Fleming
Cc: Jason Jin
Cc: Stefano Babic
Cc: Daniel Schwierzeck
Acked-by: Stefano Babic
Acked-by: Daniel Schwierzeck
15 May, 2012
1 commit
-
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.Signed-off-by: Nobuhiro Iwamatsu
CC: Stefano Babic
Acked-by: Stefano Babic
28 Mar, 2012
1 commit
-
Drop direct access to SOC's registers and use
the function of the GPIO driver for da8xx.[Tom: Remove gpio[68]_base as it's now unused]
Signed-off-by: Stefano Babic
CC: Bastian Ruppert
CC: dzu@denx.de
CC: Sandeep Paulraj
Signed-off-by: Tom Rini
28 Feb, 2012
3 commits
-
In commit 2d575e46859dd9127a9cec731ace77523e6ea2ab a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.Signed-off-by: Prabhakar Lad
Cc: Tom Rini -
add support to read mac address for AM18x EVM manufactured from
Spectrum digital which have mac address stored in I2C EEPROM manufactured
by WINBOND. This patch reads mac address from I2C EEPROM and sets the
environment variable if not set, If mac address is already present in
environment compare it with the mac address in EEPROM and warn on
mismatch.Introduced a config option CONFIG_MAC_ADDR_IN_EEPROM to where
to look for the mac address.Signed-off-by: Manjunath Hadli
Cc: Tom Rini
Cc: Mike Frysinger
Cc: Wolfgang Denk -
add support to read mac address for da850/L138 evm manufactured by
Logic PD which store mac address in SPI flash manufactured by ST
Microelectronics. This patch adds support to read mac address from
SPI flash and set the mac address if it hasn't been set in environment,
If it has been set in the environment it compares the value one with
SPI flash and warns on mismatch. Introduced a config option
CONFIG_MAC_ADDR_IN_SPIFLASH indicating where to look mac address for.Signed-off-by: Manjunath Hadli
Cc: Tom Rini
Cc: Mike Frysinger
Cc: Wolfgang Denk
12 Feb, 2012
1 commit
-
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.Signed-off-by: Sughosh Ganu
Signed-off-by: Heiko Schocher
Cc: Heiko Schocher
Cc: Christian Riesch
Cc: Sudhakar Rajashekhara
Cc: Tom Rini
Acked-by: Christian Riesch
24 Dec, 2011
1 commit
-
Signed-off-by: Christian Riesch
Cc: Heiko Schocher
Cc: Sandeep Paulraj
Cc: Tom Rini
Cc: Sudhakar Rajashekhara
07 Dec, 2011
7 commits
-
there are two boards based on da850 SOC - OMAP-L138 and AM18x.
In order to differentiate between these two boards, revision id
is passed to kernel via second byte of ATAG_REVISION.Signed-off-by: Manjunathappa, Prakash
Signed-off-by: Manjunath Hadli -
move the board/davinci/common/misc.c file to
arch/arm/cpu/arm926ejs/davinci/misc.c, so all
davinci boards can use this functions.Signed-off-by: Heiko Schocher
Cc: Sandeep Paulraj
Cc: Tom Rini
Cc: Albert ARIBAUD
Cc: Christian Riesch -
Signed-off-by: Heiko Schocher
Cc: Sandeep Paulraj
Cc: Tom Rini
Cc: Albert ARIBAUD
Cc: Christian Riesch -
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.Signed-off-by: Christian Riesch
Cc: Sandeep Paulraj
Cc: Heiko Schocher
Cc: Syed Mohammed Khasim
Cc: Sughosh Ganu
Cc: Mike Frysinger
Acked-by: Heiko Schocher -
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the da850evm use these definitions instead of
defining its own.Signed-off-by: Christian Riesch
Cc: Sandeep Paulraj
Cc: Heiko Schocher
Cc: Sudhakar Rajashekhara
Cc: Mike Frysinger
Acked-by: Heiko Schocher -
Pinmux configuration for the EMAC was done in a separate call
of davinci_configure_pin_mux(). This patch moves all the pinmux
configuration that is done for this board to a common place.Signed-off-by: Christian Riesch
Cc: Heiko Schocher
Cc: Sandeep Paulraj
Cc: Sudhakar Rajashekhara
Acked-by: Heiko Schocher -
The configuration in struct pinmux_config i2c_pins does not configure
the pins for i2c but for uart. Since this function is already
configured by struct pinmux_config uart2_pins the i2c_pins struct
is obsolete.Signed-off-by: Christian Riesch
Cc: Heiko Schocher
Cc: Syed Mohammed Khasim
Cc: Sughosh Ganu
Cc: Sandeep Paulraj
Acked-by: Heiko Schocher