07 Feb, 2019
1 commit
-
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.Signed-off-by: Vignesh R
Tested-by: Simon Goldschmidt
Tested-by: Stefan Roese
Tested-by: Horatiu Vultur
Reviewed-by: Jagan Teki
Tested-by: Jagan Teki #zynq-microzed
01 Feb, 2019
1 commit
-
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.Signed-off-by: Tien Fong Chee
Reviewed-by: Simon Goldschmidt
Reviewed-by: Tom Rini
24 Jan, 2019
5 commits
-
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4e993476fa87d8933db0cd58d3c2d41)ZynqMP mini configurations are not moved yet and it is questionable if
make sense to move them too.Signed-off-by: Michal Simek
-
Enable fpga load secure feature for xilinx platforms.
Signed-off-by: Michal Simek
-
Enable GQSPI driver, SF command and SPL support for some platforms.
Signed-off-by: Michal Simek
-
Setup proper ETH/MMC dependency for the whole platform.
Signed-off-by: Michal Simek
-
This board contains 2 nand chips that's why enable this feature.
Signed-off-by: Michal Simek
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
16 Oct, 2018
1 commit
-
Simplify defconfig for ZynqMP but keep option not to enable it for mini
targets.Signed-off-by: Michal Simek
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMACSigned-off-by: Adam Ford
Acked-by: Jagan Teki
Acked-by: Joe Hershberger
23 Jul, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICESigned-off-by: Adam Ford
19 Jul, 2018
1 commit
-
CONFIG_MP was added to Kconfig with enabling CONFIG_DEFINE_TCM_OCM_MMAP=y
for zynqmp boards. This option is enabled by default that's why it
shouldn't be in defconfig.Signed-off-by: Michal Simek
11 Jul, 2018
1 commit
-
This patch moves CONFIG_MP to Kconfig
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
04 Jun, 2018
1 commit
-
CONFIG_DEBUG_UART_BASE and CONFIG_DEBUG_UART_CLOCK have changed that's
why this sync.Signed-off-by: Michal Simek
02 Jun, 2018
1 commit
-
Xilinx changes for v2018.07 second pull
zynqmp:
- Show reset reason
- Remove emulation platform
- Update pmufw version
- Simplify mmc bootmode
- Remove dc2 useless configuration file
- Cleanup mini config
- Defconfig syncup
- zcu100, zcu104 and zcu111 dts fixesxilinx:
- Use live-tree functions in some drivers
- Add support for Avnet Minized and Antminer S9fpga:
- Add secure bitstream loading supportmmc:
- Add hs200 mode supportusb xhci:
- Header fix
31 May, 2018
2 commits
-
Sync defconfigs.
Signed-off-by: Michal Simek
-
There is no reason to keep empty config file in the tree that's why
remove it.Signed-off-by: Michal Simek
30 May, 2018
1 commit
-
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.Signed-off-by: Alex Kiernan
Reviewed-by: Simon Glass
Acked-by: Joe Hershberger
18 May, 2018
1 commit
-
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
11 May, 2018
1 commit
-
DISPLAY_BOARDINFO in OF case show model identification string from DT.
Enable this feature instead of custom IDENT_STRING which does the same
thing.Signed-off-by: Michal Simek
Reviewed-by: Alexander Graf
17 Apr, 2018
1 commit
-
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.Signed-off-by: Alexander Graf
09 Apr, 2018
4 commits
-
This patch enables the fixed link support for
all ZynqMP boards.Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek -
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.Signed-off-by: Luca Ceresoli
Signed-off-by: Michal Simek -
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.
Signed-off-by: Mario Six
-
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini
23 Mar, 2018
2 commits
-
Make defconfigs up2date with current location.
Signed-off-by: Michal Simek
-
Use zynqmp clock driver instead of fixed clocks.
Signed-off-by: Michal Simek
02 Feb, 2018
1 commit
-
This commit moves USB_FUNCTION_THOR config to Kconfig.
Signed-off-by: Lukasz Majewski
Acked-by: Michal Simek
Reviewed-by: Jaehoon Chung
30 Jan, 2018
1 commit
-
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.Signed-off-by: Vipul Kumar
Signed-off-by: Michal Simek
15 Dec, 2017
5 commits
-
Enable fpga loadb and loadbp for zynqmp platforms.
Signed-off-by: Michal Simek
-
Signed-off-by: Michal Simek
-
Enable misc devices for zynqmp targets.
Signed-off-by: Michal Simek
-
clk command provides an option to see actual clock setting.
Signed-off-by: Michal Simek
-
This was caused by: "fs/fat: Reduce stack usage"
(sha1:2460098cffacd18729262e3ed36656e6943783ed) which converted
fat code to use malloc. But simple malloc is not freeing space
that's why full malloc implementation is needed.
Malloc space is added to RAM.Signed-off-by: Michal Simek
28 Nov, 2017
1 commit
-
Move cadence/zynq serial driver via Kconfig
Signed-off-by: Michal Simek
Reviewed-by: Simon Glass
17 Oct, 2017
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
11 Oct, 2017
1 commit
-
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.Signed-off-by: Tuomas Tynkkynen
04 Oct, 2017
1 commit
-
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass
Reviewed-by: Lukasz Majewski
Signed-off-by: Maxime Ripard
02 Sep, 2017
1 commit
-
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the READMESigned-off-by: Tom Rini