Eric Lee / smarc-uboot

16 Jun, 2020

1 commit

06 May, 2020

3 commits

10 Mar, 2020

1 commit

  • 60559d357   mx7dsabresd: Boot in non secure by default ... Browse Code »

    Booting a mainline kernel in secure mode on i.MX7D causes only
    one CPU to be brought up.

    Change it to booting in non secure mode by default, which
    allows the two CPUs to be brought up.

    It does have a side effect of not probing the CAAM driver.
    If CAAM driver is needed then a secure world OS such as OPTEE needs
    to be used.

    Signed-off-by: Fabio Estevam

    Fabio Estevam
     

23 Jan, 2020

1 commit

07 Jan, 2020

3 commits

04 Dec, 2019

1 commit

21 Nov, 2019

2 commits

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     
  • 8d8ee47e0   env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol ... Browse Code »
    24

    Today in initr_reloc_global_data() we use some non-obvious tests to
    determine if we need to relocate the env_addr within gd or not. In
    order to facilitate migration of other symbols to Kconfig we need to
    introduce a new symbol for this particular use case.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Signed-off-by: Tom Rini

    Tom Rini
     

05 Oct, 2019

1 commit

24 Aug, 2019

1 commit

23 Jun, 2019

1 commit

05 May, 2019

1 commit

  • 623de3f08   Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_SUPPORT_EMMC_BOOT

    As requested by Michal Simek , these boards
    have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

    xilinx_zynqmp_zc1275_revB
    xilinx_zynqmp_zc1751_xm018_dc4
    xilinx_zynqmp_zc1751_xm019_dc5
    xilinx_zynqmp_zcu100_revC
    xilinx_zynqmp_zcu102_rev1_0
    xilinx_zynqmp_zcu102_revA
    xilinx_zynqmp_zcu102_revB
    xilinx_zynqmp_zcu104_revA
    xilinx_zynqmp_zcu104_revC
    xilinx_zynqmp_zcu106_revA
    xilinx_zynqmp_zcu111_revA

    Signed-off-by: Alex Kiernan
    Acked-by: Lukasz Majewski
    Acked-by: Patrick Delaunay
    Acked-by: Ramon Fried
    Reviewed-by: Andy Shevchenko
    Tested-by: Sébastien Szymanski

    Alex Kiernan
     

30 Apr, 2019

1 commit

19 Jan, 2019

1 commit

  • 2acc24fc2   Kconfig: Migrate BOUNCE_BUFFER ... Browse Code »

    The bounce buffer is used by a few drivers (most of the MMC drivers)
    to overcome limitations in their respective DMA implementation.

    This moves the configuration to Kconfig and makes it user-selectable
    (even though it will be a required feature to make those drivers
    work): the expected usage is for drivers depending on this to 'select'
    it unconditionally from their respective Kconfig (see follow-up
    patches).

    This commit includes a full migration using moveconfig.py to ensure
    that each commit compiles. To ensure bisectability we update
    dependencies of various drivers to now select BOUNCE_BUFFER when needed.

    [trini: Squash all patches to ensure bisectability]
    Signed-off-by: Tom Rini
    Signed-off-by: Philipp Tomsich
    Reviewed-by: Otavio Salvador [dw_mmc portion]
    Reviewed-by: Fabio Estevam [mxsmmc portion]
    Reviewed-by: Simon Glass [tegra portion]

    Philipp Tomsich
     

04 Sep, 2018

1 commit

18 Aug, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

08 Aug, 2018

1 commit

30 Apr, 2018

1 commit

28 Apr, 2018

1 commit

  • f1b1f7706   Convert CONFIG_SPI to Kconfig ... Browse Code »

    This converts the following to Kconfig:
    CONFIG_SPI

    This partly involves updating code that assumes that CONFIG_SPI implies
    things that are specific to the MPC8xx SPI driver. For now, just update
    the CONFIG tests. This also involves reworking the default for
    CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
    reasonable default, as it does not cause any compile failures.

    Signed-off-by: Adam Ford
    Signed-off-by: Tom Rini

    Adam Ford
     

26 Apr, 2018

1 commit

  • feb14c634   mx7dsabresd: Remove the mx7dsabresd_secure_defconfig target ... Browse Code »

    mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel
    that has CAAM support and needs to boot in secure mode.

    Instead of keeping two different config targets for the same board,
    remove mx7dsabresd_secure_defconfig and select
    CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that
    this target could be used to boot both mainline and the vendor kernel.

    This makes maintenance task easier and avoid potentially confusion
    for the end user.

    Signed-off-by: Fabio Estevam
    Acked-by: Bryan O'Donoghue

    Fabio Estevam
     

09 Apr, 2018

1 commit

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

04 Feb, 2018

1 commit

  • c966c7b97   imx: mx7dsabresd: enable UHS and HS200 ... Browse Code »

    Enable UHS and HS200 for mx7dsabresd.

    Read Speed improvement:
    Kingston SD10VG2/16GB SDHC 3.0 card
    22.2MB/s -> 73.7MB/s
    eMMC5.0 MTFC8GACAEAM:
    68MB/s -> 87MB/s

    Signed-off-by: Peng Fan
    Cc: Stefano Babic
    Cc: Fabio Estevam
    Cc: Jaehoon Chung

    Peng Fan
     

29 Dec, 2017

1 commit

  • b47b70531   imx: Unify CONFIG_BOOTDELAY ... Browse Code »

    In order to provide a consistent user experience for imx board users,
    remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
    all boards can use the default two second delay.

    Signed-off-by: Fabio Estevam
    Reviewed-by: Lukasz Majewski

    Fabio Estevam
     

31 Oct, 2017

3 commits

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

04 Oct, 2017

1 commit

  • a95aee6af   usb: gadget: Make g_dnl USB settings common ... Browse Code »

    The g_dnl USB settings for the vendor ID, product ID and manufacturer are
    actually common settings that can and should be shared by all the gadgets.

    Make them common by renaming them, and convert all the users.

    Reviewed-by: Simon Glass
    Reviewed-by: Lukasz Majewski
    Signed-off-by: Maxime Ripard

    Maxime Ripard
     

08 Sep, 2017

2 commits

17 Aug, 2017

1 commit

15 Aug, 2017

1 commit

08 Aug, 2017

1 commit

19 Jun, 2017

1 commit