11 Aug, 2007
2 commits
-
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATAChanges:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >Signed-off-by: Sergey Kubushyn
Acked-by: Dirk Behme
Acked-by: Zach Sadecki
Acked-by: Stefan Roese
10 Aug, 2007
5 commits
-
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.Signed-off-by: Michael Barkowski
Signed-off-by: Kim Phillips -
MPC83xx: Fix the Makefile config sections to generate the include/config.h
file in the build directory instead of the source directory.Signed-off-by: David Saada
Signed-off-by: Kim Phillips -
Signed-off-by: Kumar Gala
08 Aug, 2007
1 commit
07 Aug, 2007
1 commit
06 Aug, 2007
4 commits
-
This patch add definition of the BIOS emulator and the ATI framebuffer
driver for MPC8641HPCN board.Signed-off-by: Jason Jin
Signed-off-by: Zhang Wei
03 Aug, 2007
2 commits
-
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running onFew minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)Signed-off-by: Grzegorz Bernacki
Signed-off-by: Piotr Kruszynski
Signed-off-by: Bartlomiej Sieka -
Conflicts:
CHANGELOG
fs/fat/fat.c
include/configs/MPC8560ADS.h
include/configs/pcs440ep.h
net/eth.c
02 Aug, 2007
2 commits
-
Signed-off-by: Wolfgang Denk
27 Jul, 2007
1 commit
-
The following MPC5121e subsystems are supported:
- low-level CPU init
- NOR Boot Flash (common CFI driver)
- DDR SDRAM
- FEC
- I2C
- WatchdogSigned-off-by: Grzegorz Bernacki
Signed-off-by: Rafal Jaworowski
Signed-off-by: Jan Wrobel
14 Jul, 2007
1 commit
12 Jul, 2007
3 commits
-
Signed-off-by: Piotr Kruszynski
Signed-off-by: Bartlomiej Sieka -
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is usedSigned-off-by: Heiko Schocher
10 Jul, 2007
1 commit
05 Jul, 2007
1 commit
-
Signed-off-by: Sergei Poselenov
04 Jul, 2007
1 commit
-
Signed-off-by: Grant Likely
23 Jun, 2007
1 commit
-
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAMSigned-off-by: Heiko Schocher
15 Jun, 2007
1 commit
-
This patch adds initial support for the Liebherr lwmon5 board euqipped
with an AMCC 440EPx PowerPC.Signed-off-by: Stefan Roese
06 Jun, 2007
7 commits
-
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND bootingSigned-off-by: Stefan Roese
-
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variableSigned-off-by: Ed Swarthout
Signed-off-by: Jon Loeliger
05 Jun, 2007
1 commit
01 Jun, 2007
2 commits
-
This patch adds NAND booting support for the AMCC Bamboo eval board.
Since the NAND-SPL boot image is limited to 4kbytes, this version
only supports the onboard 64MBytes of DDR. The DIMM modules can't be
supported, since the setup code for I2C DIMM autodetection and
configuration is too big for this NAND bootloader.Signed-off-by: Stefan Roese
31 May, 2007
2 commits
-
Signed-off-by: Wolfgang Denk
29 May, 2007
1 commit