Eric Lee / smarc-uboot

09 May, 2019

2 commits

  • 504bf790d   Merge branch 'master' of git://git.denx.de/u-boot-sunxi ... Browse Code »

    - H6 Beelink GS1 board (Clément)
    - Olimex A64-Teres-I board (Jonas)
    - sunxi build fix for CONFIG_CMD_PXE|DHCP (Ondrej)
    - Change include order (Jagan)
    - EPHY clock changes (Jagan)
    - EMAC enablement on Cubietruck Plus, BPI-M3 (Chen-Yu Tsai)

    Tom Rini
     
  • b39eab2ff   sunxi: Enable EMAC on the Cubietruck Plus ... Browse Code »

    The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using
    RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are
    powered by DLDO3 @ 2.5V.

    This patch enables the EMAC and Realtek PHY drivers in the defconfig.
    The device tree file already has the EMAC enabled.

    Signed-off-by: Chen-Yu Tsai
    Reviewed-by: Jagan Teki

    Chen-Yu Tsai
     

30 Apr, 2019

2 commits

08 Feb, 2019

1 commit

19 Jan, 2019

1 commit

  • 29d280c88   sunxi: usb: Switch to Generic host controllers ... Browse Code »

    Onc of key blocker for using USB Generic host controller
    drivers in Allwinner are CLK and RESET drivers, now these
    available for USB usage.

    So switch sunxi USB use EHCI and OHCI Generic controllers.

    Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
    where it already have USB_EHCI_HCD

    Signed-off-by: Jagan Teki
    Acked-by: Maxime Ripard

    Jagan Teki
     

04 Sep, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

17 Apr, 2018

1 commit

  • 4f67b93fb   part: Disable CONFIG_SPL_ISO_PARTITION by default ... Browse Code »

    We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
    could load distro images that usually get shipped as iso images. These images
    usually come with a board agnostic boot environment.

    However, there is very little point in having ISO support enabled (for anyone
    really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
    is board specific. So the fact that we enable ISO support in U-Boot proper does
    not mean at all that we want ISO support in U-Boot SPL.

    Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
    all those default configs that disabled SPL ISO support.

    Signed-off-by: Alexander Graf

    Alexander Graf
     

08 Apr, 2018

1 commit

14 Mar, 2018

1 commit

  • 341c05865   sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs ... Browse Code »

    Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
    CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
    of moving the common definition shared by almost every sunxi board
    into 123 individual defconfig files. But the U-Boot start address
    for Allwinner boards is a platform decision which has been around for
    ages, so defining it in each *board* config file seems a bit over the
    top.
    Define the standard values (160MB into DRAM for most SoCs, with two
    SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
    the individual defconfigs.

    Signed-off-by: Andre Przywara
    Acked-by: Maxime Ripard
    Reviewed-by: Jagan Teki

    Andre Przywara
     

11 Feb, 2018

1 commit

  • 278b90ce7   configs: Migrate CONFIG_SYS_TEXT_BASE ... Browse Code »
    15

    On the NIOS2 and Xtensa architectures, we do not have
    CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
    values into the defconfig and removing them from the headers.

    I did not attempt to add more default values in and for now will leave
    that to maintainers.

    Signed-off-by: Tom Rini

    Tom Rini
     

06 Feb, 2018

1 commit

  • a4fa81146   cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA ... Browse Code »

    cmd/Makefile has:

    ifdef CONFIG_FPGA
    obj-$(CONFIG_CMD_FPGA) += fpga.o
    endif

    which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
    does nothing. Let's remove that Makefile conditional and instead express
    this equivalent dependency in Kconfig, so a lot of redundant

    # CONFIG_CMD_FPGA is not set

    can be removed from board defconfigs that don't actually have an FPGA.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

04 Oct, 2017

1 commit

02 Sep, 2017

1 commit

  • ecad7051b   configs: Migrate all of the existing USB symbols, except fastboot ... Browse Code »
    20

    This syncs all of the currently Kconfig'd symbols out of the headers and
    into the defconfig files. This has two exceptions, first am335x_evm
    needs to be converted to DM in SPL and then it can stop undef'ing
    CONFIG_DM_USB. Leaving this as-is results in a build failure, and
    without work, run time failure. The other case is am43xx_evm.h and in
    turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
    host mode in SPL, but still desire to have gadget mode in U-Boot proper.

    Signed-off-by: Tom Rini

    Tom Rini
     

28 Jan, 2017

3 commits

24 Oct, 2016

1 commit

09 Sep, 2016

1 commit

17 Jun, 2016

1 commit

10 Jun, 2016

1 commit

25 May, 2016

1 commit

  • 0878a8a7d   sunxi: Enable a bunch of commands by default on sunxi ... Browse Code »

    Recently a set of CONFIG_CMD_FOO defines was moved from being defined
    in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
    to compensate.

    Instead of explictly selecting these in all sunxi defconfigs,
    simply always select these for sunxi boards. This makes the defconfigs
    simpler and ensures a consistent set of available commands across all
    sunxi boards.

    Signed-off-by: Hans de Goede

    Hans de Goede
     

26 Apr, 2016

3 commits

12 Apr, 2016

1 commit

  • 88bb800dd   sunxi: Enable CMD_GPIO on all sunxi boards ... Browse Code »

    We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
    its Kconfig conversion it has ended up missing on some recently
    added boards.

    Simply select it for ARCH_SUNXI, so that we get it on all
    sunxi boards for both a consistent user experience and simpler
    defconfig files.

    Signed-off-by: Hans de Goede
    Acked-by: Ian Campbell

    Hans de Goede
     

01 Apr, 2016

1 commit

  • 7e4c5d207   sunxi: Cubietruck Plus: Enable USB Kconfig options in defconfig ... Browse Code »

    The Cubietruck Plus uses all 3 USB controllers:

    - USB OTG functions are provided by the musb USB OTG controller
    - Onboard SATA is provied by a USB-SATA bridge connected to USB1
    - The USB host ports on the board are provided by an HSIC USB hub

    FLDO1 is set to 1.2V for HSIC.

    Signed-off-by: Chen-Yu Tsai
    Reviewed-by: Hans de Goede
    Signed-off-by: Hans de Goede

    Chen-Yu Tsai
     

24 Mar, 2016

1 commit

  • a9be871c1   sunxi: Add defconfig for Cubietruck Plus ... Browse Code »

    Cubietruck Plus is a A83T/H8 based development board. The board has
    standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
    via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
    WiFi, headphone out / mic in, and various GPIO headers.

    The board also has an EEPROM on i2c0 which holds the MAC address.

    DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20
    is connected to the reset control of the PHY. EMAC is not actually
    supported yet.

    Signed-off-by: Chen-Yu Tsai
    Acked-by: Hans de Goede
    Signed-off-by: Hans de Goede

    Chen-Yu Tsai