23 Mar, 2010
3 commits
-
Update CHANGELOG
Signed-off-by: Wolfgang Denk
-
ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution,
as announced by get_tbclk()Signed-off-by: Matthias Kaehlcke
-
ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid
overflows in intermediate valuesSigned-off-by: Matthias Kaehlcke
22 Mar, 2010
8 commits
-
Signed-off-by: Asen Dimov
-
The crc table was being built as little endian for big endian
targets. This would cause fw_printenv to always fail with
"Warning: Bad CRC, using default environment" messages.Signed-off-by: Jeff Angielski
Acked-by: Joakim Tjernlund -
Fix warnings while compiling with CONFIG_VIDEO enabled:
diu.c: In function 'video_hw_init':
diu.c:158: warning: 'return' with no value, in function returning non-void
diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int'
diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int'Signed-off-by: Anatolij Gustschin
-
If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.Signed-off-by: Anatolij Gustschin
-
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk -
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.Signed-off-by: Stefano Babic
-
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds.
In some cases (busy networks, slow TFTP servers) this caused very
slow transfers. A new environment variable "tftptimeout" allows to
set this timeout. Lowering this value may make downloads succeed
faster in networks with high packet loss rates or with unreliable
TFTP servers.Signed-off-by: Wolfgang Denk
Cc: Ben Warren
Signed-off-by: Ben Warren -
Signed-off-by: FUJITA Kazutoshi
Signed-off-by:
Acked-by: Stefan Roese
21 Mar, 2010
1 commit
-
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.Signed-off-by: Frans Meulenbroeks
17 Mar, 2010
2 commits
-
Signed-off-by: Scott McNutt
-
Signed-off-by: Scott McNutt
14 Mar, 2010
3 commits
-
The new zlib code wants asm/unaligned.h, so have the Blackfin version pull
in the asm-generic/unaligned.h.Signed-off-by: Mike Frysinger
-
This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.Signed-off-by: Mike Frysinger
13 Mar, 2010
4 commits
-
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.Signed-off-by: Matthias Weisser
-
Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk
-
Building examples/standalone/eepro100_eeprom triggers this error:
In file included from include/common.h:629,
from eepro100_eeprom.c:24:
include/net.h: In function 'NetReadIP':
include/net.h:430: warning: implicit declaration of function 'memcpy'
eepro100_eeprom.c: At top level:
eepro100_eeprom.c:81: error: conflicting types for 'memcpy'
include/net.h:430: error: previous implicit declaration of 'memcpy' was hereFix this.
Signed-off-by: Wolfgang Denk
-
Signed-off-by: Wolfgang Denk
12 Mar, 2010
12 commits
-
This code has compile problems and the company does not even exist any
more. So we take the liberty to drop support for it.Signed-off-by: Detlev Zundel
CC: Wolfgang Denk
CC: Ben Warren -
The 36-bit build exceeds the 512k size we have. Removing FIT type image
support allows us to fit and we dont really use it.Signed-off-by: Kumar Gala
-
Signed-off-by: Michael Zaidman
-
The length of configured MTDPARTS_DEFAULT string
could be greater than console printbuffer size.
Replace printf() by puts() to avoid potential buffer
overflows.Signed-off-by: Anatolij Gustschin
-
This patch corrects small mistake in the register list in
doc/README.mpc8536ds. These registers are 32 bits and this one starts
at ....c not ....eWhen using the ...c address I can boot from sd, when using the ...e
address I cannot.Signed-off-by: Frans Meulenbroeks
Acked-by: Hu Mingkai -
Signed-off-by: Heiko Schocher
-
Also enable support for CONFIG_HWCONFIG because we use this for
configuring if this hardware has a FEC or not.syntax:
hwconfig=fec:on if hardware has an fec
hwconfig=fec:off if hardware has no fecSigned-off-by: Heiko Schocher
Signed-off-by: Wolfgang Denk -
Also use hwconfig to configure whether the board has a FEC or not.
We then can adjust the DTS to tell Linux if there is a FEC present.syntax:
hwconfig=fec:on if hardware has a FEC
hwconfig=fec:off if hardware has no FECSigned-off-by: Heiko Schocher
Signed-off-by: Wolfgang Denk -
The auto-update feature (CONFIG_UPDATE_TFTP) requires that the env
variable serverip be set for the TFTP access. If DHCP is to be used
to get the serverip env variable, this doesn't work as DHCP happens
after the auto-update attempt has run. A solution is to run DHCP in
PREBOOT, but even this is too late.To solve this, we move update_tftp() below the PREBOOT stuff.
Signed-off-by: Wolfgang Denk
-
Some people boot images with the entry point in the middle of the blob
(like Linux with the head code in discardable .init.text), and there is no
no real requirement that the entry point be right after the mkimage header
when doing XIP, so let people specify whatever they want. If they do need
an entry right after the header, then they still can do that with normal
-e behavior.Signed-off-by: Mike Frysinger
-
This patch uses gd->relocaddr variable to store uboot's relocated
address in RAM and shows it in bdinfo command.This patch moves CONFIG_AMIGAONEG3SE style copying of the address
in board_init_f to just before relocation is actually done.Signed-off-by: Richard Retanubun
Tested-by: Detlev Zundel -
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.Reported-by: Quentin Armitage
Signed-off-by: Wolfgang Denk
08 Mar, 2010
7 commits
-
* convert otc570 board to use c stucture SoC access
* change gpio access to at91_gpio syntaxSigned-off-by: Daniel Gorsulowski
-
* updates the conditional main_clock calculation (if AT91_MAIN_CLOCK defined) to c structure SoC access
* add need register flagsSigned-off-by: Jens Scharsig
-
This patch fixes following build warning
Invalid Kwbimage command Type - valid names are: BOOT_FROM, NAND_ECC_MODE, NAND_PAGE_SIZE, SATA_PIO_MODE, DDR_INIT_DELAY, DATA, , spi, nand, sata, pex, uart
Signed-off-by: Prafulla Wadaskar
-
The patch removes warnings at compile time and provides
some cleanup code:
- Removed comment on NAND (not yet supported) from lowlevel_init.S
- Removed NFMS bit definition from imx-regs.h
The bit is only related to MX.25/35 and can lead to confusion
- Moved is_soc_rev() to soc specific code (removed from mx51evk.c)Signed-off-by: Stefano Babic
-
Supporting new machine ids for SoCs spear310 and spear320
include/asm-arm/mach-types.h has to be updated before applying
this patch for build to workSigned-off-by: Vipin Kumar
-
Signed-off-by: Heiko Schocher
-
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.cSigned-off-by: Holger Brunck
Signed-off-by: Stefan Roese
Signed-off-by: Heiko Schocher
