10 Jan, 2014
9 commits
-
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.Conflicts:
include/configs/exynos5250-dt.hSigned-off-by: Tom Rini
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM012:
- 1GB DDR3
- 64MiB Numonyx NOR flash
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
Cc: Stefan Roese -
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM013:
- 1GB DDR3
- 128 Mb Quad-SPI Flash(dual parallel)
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM010:
- 1Gb DDR3
- 1Mb SST SPI flash
- 128 Mb Quad-SPI Flash
- 8 Mb SST SI flash
- Full size SD/MMC card cage
- 10/100/1000 Ethernet
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switchFor more info - http://zedboard.org/product/microzed
Signed-off-by: Jagannadha Sutradharudu Teki
-
Zed is a complete development board based on the
Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z020-CLG484-1
Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash(
- Full size SD/MMC card cage
Connectivity:
- 10/100/1000 Ethernet
- USB OTG (Device/Host/OTG)
- USB-UART
Expansion:
- FMC (Low Pin Count)
- Pmod. headers (2x6)
Video/Display:
- HDMI output (1080p60 + audio)
- VGA connector
- 128 x 32 OLED
- User LEDs (9)
User inputs:
- Slide switches (8)
- Push button switches (7)
Audio:
- 24-bit stereo audio CODEC
- Stereo line in/out
- Headphone
- Microphone input
Analog:
- Xilinx XADC header
- Supports 4 analog inputs
- 2 Differential / 4 Single-ended
Debug:
- On-board USB JTAG programming port
- ARM Debug Access Port (DAP)For more info - http://zedboard.org/product/zedboard
Signed-off-by: Jagannadha Sutradharudu Teki
-
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.ZC702-:
APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDsFor more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htmZC706-:
APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDsFor more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htmSigned-off-by: Jagannadha Sutradharudu Teki
-
zynq.h -> zynq-common.h, zynq-common is Common
configuration options for all Zynq boards.zynq.h is no longer exists hense removed from boards.cfg
Signed-off-by: Jagannadha Sutradharudu Teki
-
The vexpress_aemv8a is the first aarch64 board in U-Boot.
As it was introduced, it gets built when "MAKEALL -a arm"
is invoked, and fails as this command is run with a 32-bit,
not 64-bit, toolchain as the cross-compiler.Introduce 'aarch64' as a valid 'MAKEALL -a' argument, treated
as 'arm' for all other intents, and change the architecture
of the vexpress_aemv8a entry in boards.cfg from 'arm' to
'aarch64'.
09 Jan, 2014
2 commits
-
Signed-off-by: David Feng
Signed-off-by: Bhupesh Sharma
08 Jan, 2014
1 commit
-
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.Signed-off-by: Tom Rini
07 Jan, 2014
1 commit
06 Jan, 2014
3 commits
-
The board is similar to the standard km_kirkwood board. From a
u-boot point of view, the only difference is an increased
256 MiB DRAM (128M16). A board based on this design is for
example the SUP12.Signed-off-by: Karlheinz Jerg
Signed-off-by: Holger Brunck -
Conflicts:
include/micrel.hThe conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
03 Jan, 2014
1 commit
-
Signed-off-by: Shaohui Xie
30 Dec, 2013
1 commit
-
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.Signed-off-by: Rajeshwari S Shinde
Signed-off-by: Akshay Saraswat
Acked-by: Simon Glass
Signed-off-by: Minkyu Kang
21 Dec, 2013
1 commit
-
With changes to the rtl8169 ethernet to improve cache support, we have
needed additional cache functions for mpc8245. As the board maintainer
has been unresponsive, remove this board.Cc: Guennadi Liakhovetski
Signed-off-by: Tom Rini
20 Dec, 2013
1 commit
-
Update boards.cfg entries for Samsung's GONI and Universal_C210 maintainers
entry.Signed-off-by: Lukasz Majewski
Acked-by: Minkyu Kang
19 Dec, 2013
3 commits
-
Adding Maintainer for AM43xx.
Signed-off-by: Lokesh Vutla
-
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.Signed-off-by: Alban Bedel
Reviewed-by: Stephen Warren
Signed-off-by: Tom Warren -
I no longer work for Avionic Design and don't have access to hardware,
so I'll pass on maintainership to Alban.Acked-by: Alban Bedel
Signed-off-by: Thierry Reding
Signed-off-by: Tom Warren
18 Dec, 2013
1 commit
-
The SH7753 EVB board has SH7753, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.This patch support the following functions:
- 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMCSigned-off-by: Yoshihiro Shimoda
Signed-off-by: Nobuhiro Iwamatsu
13 Dec, 2013
2 commits
-
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.Signed-off-by: Stefan Roese
Cc: Tapani Utriainen
Cc: Thorsten Eisbein
Cc: Tom Rini -
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.Signed-off-by: Tapani Utriainen
CC: Sandeep Paulraj
Signed-off-by: Stefan Roese
Cc: Thorsten Eisbein
Cc: Tom Rini
11 Dec, 2013
1 commit
-
Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyardNeeded manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds
09 Dec, 2013
3 commits
-
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.Signed-off-by: Mateusz Kulikowski
Signed-off-by: Andreas Bießmann -
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt
Reviewed-by: Heiko Schocher
Cc: Andreas Bießmann
Cc: Bo Shen
Signed-off-by: Andreas Bießmann -
enable support for the siemens AT91SAM9G20 based boards taurus
and axm.Signed-off-by: Roger Meier
Reviewed-by: Heiko Schocher
Cc: Andreas Bießmann
Cc: Bo Shen
Signed-off-by: Andreas Bießmann
06 Dec, 2013
1 commit
04 Dec, 2013
2 commits
-
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.Signed-off-by: Lars Poeschel
-
Add cm_t335 board directory, config file. Enable build.
Signed-off-by: Ilya Ledvich
Signed-off-by: Igor Grinberg
[trini: Adapt Makefile]
Signed-off-by: Tom Rini
03 Dec, 2013
2 commits
-
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.This patch supports the following functions:
- DDR3-SDRAM
- SCIFSigned-off-by: Nobuhiro Iwamatsu
Signed-off-by: Hisashi Nakamura
CC: Nobuhiro Iwamatsu
CC: Albert Aribaud -
The lager board has R8A7790, 4GB DDR3-SDRAM, USB, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIFSigned-off-by: Kouei Abe
Signed-off-by: Hisashi Nakamura
Signed-off-by: Ryo Kataoka
Signed-off-by: Nobuhiro Iwamatsu
CC: Nobuhiro Iwamatsu
CC: Albert Aribaud
28 Nov, 2013
1 commit
-
Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.Signed-off-by: Giuseppe Pagano
Tested-by: Fabio Estevam
CC: Stefano Babic
CC: Fabio Estevam
26 Nov, 2013
3 commits
-
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.Signed-off-by: Shengzhou Liu
-
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVTSigned-off-by: Shengzhou Liu
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun -
Update T1040QDS naem to Poonam Aggrwal.
Signed-off-by: Priyanka Jain
14 Nov, 2013
1 commit
-
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personalityT1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C portsSigned-off-by: Poonam Aggrwal
Signed-off-by: Prabhakar Kushwaha
Signed-off-by: Priyanka Jain