05 Dec, 2019
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
04 Dec, 2019
1 commit
-
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
[trini: Add Kconfig files]
Signed-off-by: Tom Rini
21 Nov, 2019
2 commits
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
08 Nov, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
22 Oct, 2019
1 commit
-
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================Signed-off-by: Patrice Chotard
Acked-by: Patrick Delaunay
06 May, 2019
2 commits
-
Disable unused PINCTRL_FULL flag.
Series-cc: pde, cke, pch, uboot-stm32
Cover-letter:
SPI flash STM32 MCU's fixesThis series update MCU's DT in order to fix SPI flash
configuration:
- Adds MPU region dedicated for SPI flash used in memory mapped mode.
- Fixes compatible string.
- Fixes memory map size.
- Updates spi-tx-bus-width and spi-rx-bus-width property values.
- Adds QSPI flash support for STM32F469-disco board
ENDSigned-off-by: Patrice Chotard
-
Enable CMD_SF, MTD, DM_SPI_FLASH, SPI_FLASH, SPI, DM_SPI and
STM32_QSPI flags to be able to use the embedded n25q128a QSPI flash
on stm32f469-disco board.Signed-off-by: Patrice Chotard
30 Apr, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
13 Feb, 2019
1 commit
-
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILESigned-off-by: Heinrich Schuchardt
Reviewed-by: Simon Glass
Reviewed-by: Patrice.Chotard@st.com
Signed-off-by: Alexander Graf
16 Jan, 2019
1 commit
-
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes.Remove CONFIG_OF_EMBED from all stm32 config files which are using
this flag.Signed-off-by: Patrice Chotard
04 Sep, 2018
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
18 Aug, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_MISC_INIT_RSigned-off-by: Adam Ford
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini
17 Aug, 2018
1 commit
-
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.Signed-off-by: Tom Rini
14 Aug, 2018
1 commit
-
Add DISTRO_DEFAULT support to be able to boot on mmc
by default on boot.Signed-off-by: Patrice Chotard
04 Aug, 2018
1 commit
-
CONFIG_BLK config flag becomes mandatory, enable it.
Signed-off-by: Patrice Chotard
14 Mar, 2018
1 commit
-
Enable DOS_PARTITION for boards STM32F429-eval, STM32F469-disco
and STM32F746-disco.
This allows to read FAT partition on mmc.Signed-off-by: Patrice Chotard
24 Feb, 2018
1 commit
-
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIGSigned-off-by: Adam Ford
[trini: Re-run the migration]
Signed-off-by: Tom Rini
11 Feb, 2018
1 commit
-
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.I did not attempt to add more default values in and for now will leave
that to maintainers.Signed-off-by: Tom Rini
20 Jan, 2018
2 commits
-
Move system flags from defconfig to mach-stm32/Kconfig
Signed-off-by: Patrice Chotard
Reviewed-by: Vikas Manocha -
Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.Signed-off-by: Patrice Chotard
Reviewed-by: Vikas Manocha
10 Jan, 2018
1 commit
-
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectorsSigned-off-by: Patrice Chotard