18 Mar, 2016
4 commits
-
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.Signed-off-by: Michal Simek
Reviewed-by: Simon Glass
Reviewed-by: Tom Rini
Moved the new field to the end of the struct to avoid problems:
Signed-off-by: Simon Glass -
This reverts commit 71105f50fedddfa5b0535d102c3d5078671721ad.
The reverted commit was applied for a temporary to unbreak
few Exynos boards on the release.After the discussion about the change, this commit should be avoided.
Fixed device-tree for Exynos, allows reverting it without any issues.Signed-off-by: Przemyslaw Marczak
Cc: Stefan Roese
Cc: Tom Rini
Cc: Simon Glass
Cc: Stephen Warren
Cc: Stephen Warren
Tested-by: Simon Glass
Acked-by: Simon Glass -
This change is required to avoid warnings about invalid
size-cells defined in device-tree pinctrl nodes for Exynos.Tested on:
- Odroid U3
- Odroid XU3Signed-off-by: Przemyslaw Marczak
Cc: Stefan Roese
Cc: Tom Rini
Cc: Simon Glass
Cc: Stephen Warren
Cc: Stephen Warren
Tested-by: Simon Glass
Acked-by: Simon Glass
Acked-by: Minkyu Kang -
Some controllers do not allow the output value to be read. Detect this and
report the error in that case.Signed-off-by: Simon Glass
17 Mar, 2016
36 commits
-
Since dhry_per_sec is a u64 we must also use lldiv here when working
with it. Otherwise:
../lib/dhry/cmd_dhry.c:(.text.do_dhry+0xd8): undefined reference to `__udivdi3'On some platforms.
Signed-off-by: Tom Rini
-
This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIeNot supported yet is:
- I2C
- USB 3.0Signed-off-by: Stefan Roese
Cc: Simon Glass
Cc: Bin Meng
Reviewed-by: Bin Meng -
This adds basic support for chromebook_samus. This is the 2015 Pixel and
is based on an Intel broadwell platform.Supported so far are:
- Serial
- SPI flash
- SDRAM init (with MRC cache)
- SATA
- Video (on the internal LCD panel)
- KeyboardVarious less-visible drivers are provided to make the above work (e.g. PCH,
power control and LPC).The platform requires various binary blobs which are documented in the
README. The major missing feature is USB3 since the existing U-Boot support
does not work correctly with Intel XHCI controllers.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Sometimes it is useful to jump into U-Boot directly from coreboot or UEFI
without any 16-bit init. This can help during development by allowing U-Boot
to avoid doing all the init required by the platform.U-Boot expects its GDT to be set up correctly by its 16-bit code. If
coreboot doesn't do this (because it hasn't run the payload setup code yet)
then this won't happen.In this case we cannot rely on the GDT settings. U-Boot will hang or crash
if these are wrong. Provide a development-only option to set up the GDT
correctly. This is just a hack so you can jump to U-Boot from any stage of
coreboot, not just at the end.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
This is not needed now that the memory controller driver has the SPD data
in its own node.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Adjust the existing implementation to use the new common SDRAM init code.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
The code to call the memory reference code is common to several Intel CPUs.
Add common code for performing this init. Intel calls this 'Pre-EFI-Init'
(PEI), where EFI stands for Extensible Firmware Interface.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
The SATA indexed register write functions are common to several Intel PCHs.
Move this into a common location.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
At present samus reports about 5600 DMIPS. With the default iteration count
this is OK, but if 10 million runs are performed it overflows. Fix it.Signed-off-by: Simon Glass
-
This is missing, with causes lldiv() to fail on boards with use the private
libgcc. Add the missing routine.Code is available for using the CLZ instruction but it is not enabled at
present.This comes from coreboot version 4.0.
Signed-off-by: Simon Glass
-
There is an extra line in the comment in the header. Remove it.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Add a function to set the ID in the IOAPIC.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Update a few points which have become out-of-date.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
This is a little easier on the eyes, particularly when the backlight is set
to maximum.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Add an address which can be used for loading and running the reference code
when needed.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Add a video driver for Intel's broadwell integrated graphics controller.
This uses a binary blob for most init, with the driver just performing a few
basic tasks.This driver supports VESA as the mode-setting mechanism. Since most boards
don't support driver model yet with VESA, a special case is added to the
Kconfig for broadwell. Eventually all boards will use driver model and this
can be removed.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Provide a way to determine the HSIO (high-speed I/O) version supported by
the Intel Management Engine (ME) implementation on the platform.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Add a GPIO driver for the GPIO peripheral found on broadwell devices.
Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Broadwell uses a binary blob called the memory reference code (MRC) to start
up its SDRAM. This is similar to ivybridge so we can mostly use common code
for running this blob.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Broadwell requires quite a bit of power-management setup. Add code to set
this up correctly.Signed-off-by: Simon Glass
Acked-by: Bin Meng
[squashed in http://patchwork.ozlabs.org/patch/598373/]
Signed-off-by: Bin Meng -
Broadwell needs a special binary blob to set up the PCH. Add code to run
this on start-up.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Add a driver for the broadwell LPC (low-pin-count peripheral). This mostly
uses common code.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Add a driver for the broadwell northbridge. This sets up the location of
several blocks of registers.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Add a SATA driver for broadwell. This supports connecting an SSD and the
usual U-Boot commands to read and write data.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Add a driver for the broadwell low-power platform controller hub.
Signed-off-by: Simon Glass
Acked-by: Bin Meng -
This adds the broadwell architecture, with the CPU driver and some useful
header files.Signed-off-by: Simon Glass
Acked-by: Bin Meng -
Make a few minor updates to make the meaning clearer.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Intel has invented yet another binary blob which firmware is required to
run. This is run after SDRAM is ready. It is linked to load at a particular
address, typically 0, but is a relocatable ELF so can be moved if required.Add support for this in the build system. The file should be placed in the
board directory, and called refcode.elf.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
We don't need this anymore - we can use device tree and the new pinconfig
driver instead.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Rather than setting up the pin configuration in the GPIO driver, use the
new pinctrl driver to do it.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Add a driver which sets up the pin configuration on x86 devices with an ICH6
(or later) Platform Controller Hub.The driver is not in the pinctrl uclass due to some oddities of the way x86
devices work:- The GPIO controller is not present in I/O space until it is set up
- This is done by writing a register in the PCH
- The PCH has a driver which itself uses PCI, another driver
- The pinctrl uclass requires that a pinctrl device be available before any
other device can be probedIt would be possible to work around the limitations by:
- Hard-coding the GPIO address rather than reading it from the PCH
- Using special x86 PCI access to set the GPIO address in the PCHHowever it is not clear that this is better, since the pin configuration
driver does not actually provide normal pin configuration services - it
simply sets up all the pins statically when probed. While this remains the
case, it seems better to use a syscon uclass instead. This can be probed
whenever it is needed, without any limitations.Also add an 'invert' property to support inverting the input.
Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
At present pin configuration on link does not use the standard mechanism,
but some rather ugly custom code. As a first step to resolving this, add the
pin configuration to the device tree.Four of the GPIOs must be available before relocation (for SDRAM pin
strapping).Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Each CPU needs to have its microcode loaded. Add support for this so that
all CPUs will have the same version.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
Enable the microcode feature so that the microcode version is shown with the
'cpu detail' command.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng -
As each core starts up, record its microcode version and CPU ID so these can
be presented with the 'cpu detail' command.Signed-off-by: Simon Glass
Reviewed-by: Bin Meng
