11 Sep, 2017
12 commits
-
Add Kconfig option SPL_GZIP and SPL_ZLIB to enable gunzip support for
SPL boot, eg. falcon boot compressed kernel image.Signed-off-by: York Sun
Reviewed-by: Tom Rini
Reviewed-by: Simon Glass -
Fix warning "cast from pointer to integer of different size".
Signed-off-by: York Sun
Reviewed-by: Tom Rini -
The image size should be added to the initial pbl command, not bit
"ORed".Signed-off-by: York Sun
-
Signed-off-by: Udit Agarwal
[YS: dropped redundant commit message]
Reviewed-by: York Sun -
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.Signed-off-by: Udit Agarwal
[YS: revised commit message]
Reviewed-by: York Sun -
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.Signed-off-by: Sumit Garg
Tested-by: Vinitha Pillai
Reviewed-by: York Sun -
QE_IRAM_READY should be set only after successfully uploading the
firmware.Signed-off-by: Zhao Qiang
Reviewed-by: York Sun -
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.Signed-off-by: Ashish Kumar
Signed-off-by: Prabhakar Kushwaha
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun -
At present the IDE device number is initialized to -1, which means
we cannot type "ide read" command before setting the device number
via "ide device #".For convenience, let's set the first device as the default one.
Signed-off-by: Bin Meng
Reviewed-by: Simon Glass -
When there is no CDROM inserted, the block size is zero hence there
is no need to create a BLK device for it.Signed-off-by: Bin Meng
Reviewed-by: Simon Glass -
This converts the IDE driver to driver model so that block read and
write are fully functional.Fixes: b7c6baef ("x86: Convert MMC to driver model")
Reported-by: Heinrich Schuchardt
Signed-off-by: Bin Meng
Reviewed-by: Simon Glass
Tested-by: Heinrich Schuchardt -
So far these are using magic numbers. Replace them with macros.
Signed-off-by: Bin Meng
Reviewed-by: Simon Glass
09 Sep, 2017
2 commits
-
This board does dwc3 gadget, not host, so we cannot have host support or
we will fail to link.Signed-off-by: Tom Rini
-
The underlying implementation for ENV_AES has security complications and
is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226
for more details. Mark this as deprecated now and delete this in the
medium term if no one comes forward to re-work the support.Signed-off-by: Tom Rini
08 Sep, 2017
16 commits
-
A number of the config options for USB networking have been migrated to
Kconfig. Update README.usb to reflect this.Signed-off-by: Chris Packham
-
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.Signed-off-by: Chris Packham
Reviewed-by: Simon Glass -
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.Signed-off-by: Chris Packham
Reviewed-by: Simon Glass -
This is not a valid option. Drop it.
Signed-off-by: Chris Packham
Reviewed-by: Simon Glass -
This is not a valid option. Drop it.
Signed-off-by: Chris Packham
Reviewed-by: Simon Glass -
The correct name is 'gd->fdt_blob', not 'gd->blob'.
Signed-off-by: Nobuhiro Iwamatsu
CC: Simon Glass
Reviewed-by: Simon Glass -
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang
Acked-by: Philipp Tomsich
Reviewed-by: Philipp Tomsich -
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.Signed-off-by: Kever Yang
Acked-by: Philipp Tomsich
Reviewed-by: Philipp Tomsich -
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying
the memory {} nodes in the DT passed to the Linux kernel. The R8A779x
DT contains multiple memory {} nodes, while U-Boot only modifies the
first one and stuffs all the memory entries into it, which is wrong.
Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to
fix the issue this close to the release, while the real fix is to
extend the fdt_fixup_memory_banks() to handle multiple memory nodes
in DT.Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu -
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock
must be divided by 4 rather than 2 because a hardware workaround present
only in the H3 ES1.0 has been removed from these chips. U-Boot currently
only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider
to 4 to prevent SD instability.Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu -
%s/Desriptor/Descriptor/g
Signed-off-by: Heinrich Schuchardt
Acked-by: Joe Hershberger -
Signed-off-by: Madalin Bucur
Acked-by: Joe Hershberger
Acked-by: York Sun -
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default
of 1024. There are in fact no in-tree users that increase this size.
Adjust the comment to reflect what could be done in the future in
conjunction with CONFIG_IP_DEFRAG.Cc: Joe Hershberger
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger -
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for
PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and
disable it for PHY_INTERFACE_MODE_RGMII.Based on a similar change made in the Linux Realtek PHY driver
by Martin Blumenstingl .Signed-off-by: Madalin Bucur
Acked-by: Joe Hershberger
Acked-by: York Sun
07 Sep, 2017
8 commits
-
Delete one redundant 'which' for SPL_ATF_SUPPORT description.
Signed-off-by: Kever Yang
-
Remove a comment line refering to a non-existent file.
Signed-off-by: Heinrich Schuchardt
-
The inline documentation of vsprintf mentions a parameter size
which does not exist in the function declaration.int vsprintf(char *buf, const char *fmt, va_list args);
Signed-off-by: Heinrich Schuchardt
-
This reverts commit 25877d4e4c45451c5398aec3de50e0d5befe0e9f.
This is a workaround for Raspberry Pi boot failures seen when passing on
the device tree provided by the Raspberry Pi firmware at boot. Without
CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try
to boot Linux with this device tree.Signed-off-by: Paul Barker
Cc: Simon Glass
Tested-by: Jonathan Gray
Reviewed-by: Simon Glass -
Some files are generated during libfdt build. Ignore them.
This was wrongly put in the .gitignore in the root directory before.
Now let's remove entries there and put them in the right place.Fixes: 34e2c285 ("gitignore: add intermediates from libfdt build")
Signed-off-by: Bin Meng -
These are currently out of alphabetical order.
Signed-off-by: Bin Meng
-
Signed-off-by: Alison Chaiken
-
Change to use 'debug' to output the error message if it fails to
read the driver descriptor block.Signed-off-by: Bin Meng
06 Sep, 2017
2 commits
-
The target is not currently mentioned anywhere. Add it to the help so
people can find it.Signed-off-by: Simon Glass
-
This was broken by the recent environment refactoring. Specifically:
$ make environ
scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory
make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop.
make: *** [Makefile:1469: environ] Error 2Fix this by updating the Makefile and adjusting the #include filesnames in
two C files.Fixes: ec74f5f (Makefile: Rename 'env' target to 'environ')
Reported-by: Måns Rullgård
Signed-off-by: Simon Glass
