08 Jul, 2014
35 commits
-
For proper displayport performance, scrambling has to be enabled, but
is turned off on DP501 by default.Signed-off-by: Dirk Eibach
-
Signed-off-by: Dirk Eibach
-
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default.
Allow EDID only to avoid I2C address conflicts.Signed-off-by: Dirk Eibach
-
Signed-off-by: Dirk Eibach
-
PPC4xx config options were not complete.
ICS8N3QV01 and SIL1178 needed some more configuration.Signed-off-by: Dirk Eibach
-
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.Signed-off-by: Dirk Eibach
-
There is a new iocon hardware flavor, supporting DisplayPort finally.
Signed-off-by: Dirk Eibach
-
Signed-off-by: Dirk Eibach
-
Signed-off-by: Dirk Eibach
-
readl was called with values instead of pointers to these values.
Why this ever did work is a mystery...Signed-off-by: Dirk Eibach
-
Since ARRAY_SIZE macro is defined in include/common.h,
re-defining it in arch-specific files is redundant.Signed-off-by: Masahiro Yamada
Acked-by: Stefan Roese
Acked-by: Sonic Zhang -
Add invalidate_dcache_range() and flush_dcache_range() for the blackfin
architecture. Such functions already exist on this arch with different
names, so just forward the call.This fixes the build of bf609-ezkit board as it uses
drivers/net/designware.c which requires the above functions.Cc: Sonic Zhang , Alexey Brodkin
Signed-off-by: Vasili Galka -
get_sclk() was not defined in bfin_wdt.c, include the corresponding header.
Cc: Sonic Zhang
Signed-off-by: Vasili Galka -
The csarX and cscrX registers in the fbcs_t struct are 16-bit for
CONFIG_M5235 and 32-bit wide otherwise. The code in cpu_init.c
accessed them always as 32-bit, effectively creating a wrong memory
access on M5235. Fixed that by choosing out_be16/out_be32 depending
on whether CONFIG_M5235 is defined or not.Cc: Jason Jin
Signed-off-by: Vasili Galka -
in_be16() shall be passed a pointer to register and not its value. This
is clearly a typo resulting in a wrong memory access, so fix it.Cc: Alison Wang , Jason Jin
Signed-off-by: Vasili Galka -
This board is old enough and has no maintainer.
Signed-off-by: Masahiro Yamada
-
This board is old enough and has no maintainer.
Signed-off-by: Masahiro Yamada
-
These boards are old enough and have no maintainers.
Signed-off-by: Masahiro Yamada
-
These boards are old enough and have no maintainers.
Signed-off-by: Masahiro Yamada
-
This board is old enough and has no maintainer.
Signed-off-by: Masahiro Yamada
-
These boards are old enough and have no maintainers.
Signed-off-by: Masahiro Yamada
-
These boards are old enough and have no maintainers.
Signed-off-by: Masahiro Yamada
-
clang is tempted to inteprete such a condition as a assignment
as well. Since it isn't don't use double brackets.cc: Tom Wai-Hong Tam
Signed-off-by: Jeroen Hofstee -
Signed-off-by: Jeroen Hofstee
-
The option can be used to save the environment in spi flash.
Implementation code is already exist in command/env_sf.c. But
the documentation is missing.This patch add the details for this option to the README file.
Signed-off-by: Josh Wu
Reviewed-by: Jagannadha Sutradharudu Teki -
Use get_device_and_partition() is better since:
1. It will call the device initialize function internally. So we can
remove the mmc intialization code to save many lines.
2. It is used by fatls/fatload/fatwrite. So saveenv & load env should
use it too.
3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct
device and partition information by run-time.Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string:
FAT_ENV_DEVICE_AND_PART.
For at91sam9m10g45ek, it is "0". That means use device 0 and if:
a)device 0 has no partition table, use the whole device as a FAT file
system.
b)device 0 has partittion table, use the partition #1.Refer to the commit: 10a37fd7a4 for details of device & partition string.
Signed-off-by: Josh Wu
Reviewed-by: Stephen Warren -
* This is done by limiting the ARM's bandwidth and setting DSS priority in
the EMIF controller to ensure underflows do not occur. -
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.Signed-off-by: Franklin S. Cooper Jr
-
Make it clear that we need to load a legacy-formatted (aka uImage)
kernel into memory as well as the DT if used before using "spl export".Cc: Yebio Mesfin
Signed-off-by: Tom Rini -
J6 EVM can be built with UART3 as console, but currently
there's nothing muxing UART3 correctly. Likely this only
works because, based on commit log, author was only testing
with UART3 boot and - I assume - ROM code leave UART3 correctly
muxed in that case.If we want to boot from MMC and still use UART3 as console,
then we need to mux those signals correctly.Signed-off-by: Felipe Balbi
-
The directory arch/${ARCH}/cpu/${CPU} does not exist
in avr32, blackfin, microblaze, nios2, openrisc, sandbox, x86.These architectures have only one CPU type.
Defining CPU should not be required for such architectures.This commit allows cpu field (= the 3rd field of boards.cfg)
to be kept blank.Signed-off-by: Masahiro Yamada
Cc: Andreas Bießmann
Cc: Simon Glass
Cc: Sonic Zhang
Cc: Michal Simek
Cc: Thomas Chou
Cc: Stefan Kristiansson -
In README file, add document for the missing configuration option:
CONFIG_ENV_IS_IN_FAT.Signed-off-by: Josh Wu
Reviewed-by: Stephen Warren -
Commit 7d89982b stopped creating symbolic link
arch/${arch}/include/asm/proc.We do not need to delete it by "make mrproper" any more.
Signed-off-by: Masahiro Yamada
Cc: Vasili Galka -
The code intends for the CM_DLL_READYST to be set, but
actually polls till any bit is set since the logical
AND is used instead of the bitwise one is used. Fix it.cc: Lokesh Vutla
Signed-off-by: Jeroen Hofstee -
We need to subtract two hex numbers. Avoid using strtonum() by doing the
subtraction in bc with a suitable input base.Signed-off-by: Simon Glass
Reported-by: Vasili Galka
07 Jul, 2014
1 commit
05 Jul, 2014
4 commits
-
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.Signed-off-by: Chin Liang See
Cc: Wolfgang Denk
Cc: Detlev Zundel
Cc: Pavel Machek
Cc: Dinh Nguyen
Acked-by: Detlev Zundel -
Turn on generic board for the integrators, as per the request in
the startup message. Everything just works, tested on the
Integrator/AP and Integrator/CP.Signed-off-by: Linus Walleij
Acked-by: Simon Glass -
Serial port, SD card, and LCD all work.
Signed-off-by: Stephen Warren
Acked-by: Simon Glass -
Signed-off-by: Christian Riesch
