Eric Lee / smarc-uboot

23 Jan, 2020

1 commit

05 Dec, 2019

1 commit

21 Nov, 2019

2 commits

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     
  • 8d8ee47e0   env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol ... Browse Code »
    24

    Today in initr_reloc_global_data() we use some non-obvious tests to
    determine if we need to relocate the env_addr within gd or not. In
    order to facilitate migration of other symbols to Kconfig we need to
    introduce a new symbol for this particular use case.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Signed-off-by: Tom Rini

    Tom Rini
     

08 Nov, 2019

1 commit

26 Aug, 2019

1 commit

02 Aug, 2019

1 commit

  • 37304aaf6   Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig ... Browse Code »
    4

    This converts the following to Kconfig:
    CONFIG_USE_PREBOOT
    CONFIG_PREBOOT

    Both are together in one commit, since otherwise the former causes kconfig
    to define the latter, which gives duplicate symbol errors.

    Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
    backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

    Signed-off-by: Simon Glass

    Simon Glass
     

15 Jun, 2019

1 commit

27 May, 2019

1 commit

18 May, 2019

1 commit

  • 100150254   CONFIG_SPL_SYS_[DI]CACHE_OFF: add ... Browse Code »

    While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
    where these configuration items are conditional on SPL. This commit adds SPL
    variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
    the configurations as required.

    Acked-by: Alexey Brodkin
    Signed-off-by: Trevor Woerner
    [trini: Make the default depend on the setting for full U-Boot, update
    more zynq hardware]
    Signed-off-by: Tom Rini

    Trevor Woerner
     

30 Apr, 2019

1 commit

26 Mar, 2019

1 commit

  • 14453fbfa   Convert CONFIG_SF_DEFAULT_* to Kconfig ... Browse Code »
    36

    This converts the following to Kconfig:
    CONFIG_SF_DEFAULT_BUS
    CONFIG_SF_DEFAULT_CS
    CONFIG_SF_DEFAULT_MODE
    CONFIG_SF_DEFAULT_SPEED

    I use moveconfig script and then manual check on generated u-boot.cfg
    to solve the remaining issue.

    Signed-off-by: Patrick Delaunay

    Patrick Delaunay
     

22 Feb, 2019

1 commit

14 Feb, 2019

1 commit

  • d13f92b74   ARM: zynq: Run distribution boot commands first ... Browse Code »

    This patch is doing two things.
    1. Exchanging order of boot commands. distro_bootcmd is run first
    followed by Xilinx boot command.
    2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
    creating Xilinx distribution bootcommand and wiring it as the last
    bootcommand.

    QSPI, NAND distribution boot command will be added later.

    Signed-off-by: Michal Simek

    Michal Simek
     

07 Feb, 2019

2 commits

  • 6d8251783   configs: Don't use SPI_FLASH_BAR as default ... Browse Code »
    12

    Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
    don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
    4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
    renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
    not break functionality.

    Signed-off-by: Vignesh R
    Tested-by: Simon Goldschmidt
    Tested-by: Stefan Roese
    Tested-by: Horatiu Vultur
    Reviewed-by: Jagan Teki
    Tested-by: Jagan Teki #zynq-microzed

    Vignesh R
     
  • 75b2ec2a2   configs: Remove SF_DUAL_FLASH ... Browse Code »

    SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
    SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
    enums yield no user and therefore support seems to be incomplete. Remove
    these configs so as to avoid confusion.

    Signed-off-by: Vignesh R
    Reviewed-by: Jagan Teki
    Tested-by: Jagan Teki #zynq-microzed

    Vignesh R
     

24 Jan, 2019

1 commit

08 Jan, 2019

1 commit

04 Sep, 2018

1 commit

04 Jun, 2018

1 commit

11 May, 2018

1 commit

  • 0b4b82ad1   arm: zynq: Remove checkboard and enable DISPLAY_CPUINFO ... Browse Code »

    Now that showing silicon version is part of the CPU
    info display, let's remove checkboard().

    Note that the generic show_board_info() will still
    show the DT 'model' property. For instance:

    U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)

    CPU: Zynq 7z045
    Silicon: v1.0
    Model: Zynq ZC706 Development Board
    I2C: ready

    Based on patches from Ariel D'Alessandro ,
    and Ezequiel Garcia

    mini configuration doesn't need to show this information.

    Signed-off-by: Michal Simek

    Michal Simek
     

17 Apr, 2018

1 commit

12 Apr, 2018

1 commit

09 Apr, 2018

1 commit

23 Mar, 2018

1 commit

01 Mar, 2018

3 commits

28 Feb, 2018

1 commit

02 Feb, 2018

1 commit

30 Jan, 2018

3 commits

15 Dec, 2017

1 commit

28 Nov, 2017

2 commits

11 Oct, 2017

1 commit

  • ad12dc184   cmd: Toggle the default value of CONFIG_CMD_IMLS ... Browse Code »

    Having this as a 'default y' is rather annoying because it doesn't
    actually compile unless other options are defined in the board header:

    ../cmd/bootm.c: In function 'do_imls_nor':
    ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
    i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

    Make it 'default n' so people who develop new boards that start from a
    blank defconfig have one less compilation failure to debug.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

04 Oct, 2017

1 commit

  • a95aee6af   usb: gadget: Make g_dnl USB settings common ... Browse Code »

    The g_dnl USB settings for the vendor ID, product ID and manufacturer are
    actually common settings that can and should be shared by all the gadgets.

    Make them common by renaming them, and convert all the users.

    Reviewed-by: Simon Glass
    Reviewed-by: Lukasz Majewski
    Signed-off-by: Maxime Ripard

    Maxime Ripard
     

28 Aug, 2017

1 commit

15 Aug, 2017

1 commit