05 Feb, 2021
1 commit
-
Enable GIC_V3_ITS config to initialize the GIC redistributor
tables.Signed-off-by: Hou Zhiqiang
19 Oct, 2020
1 commit
-
Since the HDP will be shared with i.MX. Move the common HDP library
codes to "driver/video/nxp/hdp" directory.
And use platform specified directory "driver/video/nxp/layerscape"
for LS driver codes and configurations.Signed-off-by: Ye Li
Reviewed-by: Alison Wang
29 Sep, 2020
1 commit
-
This patch adds a command to load the HDP firmware and supporting
libraries.Signed-off-by: Oliver Brown
Signed-off-by: Alison Wang
02 Sep, 2020
1 commit
-
Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platformsSigned-off-by: Wasim Khan
03 Jun, 2020
1 commit
-
The switch driver for LS1028A Ethernet switch is now compiled in for
both LS1028A boards.Signed-off-by: Alex Marginean
Signed-off-by: Claudiu Manoil
30 Mar, 2020
1 commit
-
The eMMC HS200 speed mode on Layerscape platforms has not been
supported properly. The eSDHC clock tuning has not been implemented
by now. So disable it until it is supported properly in case of
any potential issues.Signed-off-by: Yangbo Lu
Reviewed-by: Jaehoon Chung
Signed-off-by: Priyanka Jain
04 Feb, 2020
1 commit
-
Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: Kuldeep Singh
Reviewed-by: Priyanka Jain
23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
16 Jan, 2020
1 commit
-
The SDHC clock divider value for LS1028A should be default 2,
not 1.Signed-off-by: Yangbo Lu
26 Dec, 2019
3 commits
-
enable ls1028ardb ugreen usb network card AX88179 and AX8817X driver
Signed-off-by: Yinbo Zhu
Signed-off-by: Priyanka Jain -
Enable ls1028ardb usb net r8152_eth
Signed-off-by: Yinbo Zhu
Signed-off-by: Priyanka Jain -
Enable 4-byte Fast Read command for Flexspi AHB mode
Signed-off-by: Kuldeep Singh
Signed-off-by: Priyanka Jain
05 Dec, 2019
2 commits
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
-
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.Signed-off-by: Miquel Raynal
Reviewed-by: Boris Brezillon
29 Nov, 2019
1 commit
-
Since at least some of the drivers relevant to LS1028A are now following
DM, it's useful to have dm command enabled by default.Signed-off-by: Alex Marginean
Reviewed-by: Priyanka Jain
27 Nov, 2019
1 commit
-
LS1028A QDS board supports multiple combinations of SerDes protocols and
multiple add-on cards with Ethernet PHYs. Some of them require specific
configuration in Linux DT, and the plan is to use DT overlays for them.Signed-off-by: Alex Marginean
Reviewed-by: Priyanka Jain
21 Nov, 2019
1 commit
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt
08 Nov, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
23 Sep, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
12 Sep, 2019
1 commit
-
Enable CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK and
CONFIG_MMC_HS200_SUPPORT config for
ls1012ardb, ls1012ardb, lx2160ardb
in defconfig fileSigned-off-by: Yinbo Zhu
Signed-off-by: Priyanka Jain
22 Aug, 2019
1 commit
-
Enable related configs on all ls1028aqds boards to support pcf2127
rtc DM function.Signed-off-by: Chuanhua Han
Reviewed-by: Alex Marginean
Tested-by: Alex Marginean
Reviewed-by: Prabhakar Kushwaha
14 Aug, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
26 Jul, 2019
1 commit
-
Enables ethernet, MDIO, PHY drivers for LS1028A RDB and QDS.
Signed-off-by: Alex Marginean
Reviewed-by: Bin Meng
Acked-by: Joe Hershberger
23 Jun, 2019
1 commit
-
Moved CONFIG_FSL_ESDHC from header files to defconfig files.
Signed-off-by: Yangbo Lu
Tested-by: Steffen Dirkwinkel
Reviewed-by: Peng Fan
Reviewed-by: Lukasz Majewski
Reviewed-by: Martyn Welch
Acked-by: Jason Liu
19 Jun, 2019
1 commit
-
LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0. ECAM plus the device register space takes up 256MB of address
space.Signed-off-by: Alex Marginean
Reviewed-by: Bin Meng
Reviewed-by: Prabhakar Kushwaha
22 May, 2019
2 commits
-
Signed-off-by: Zhao Qiang
Reviewed-by: Prabhakar Kushwaha -
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.Signed-off-by: Sudhanshu Gupta
Signed-off-by: Rai Harninder
Signed-off-by: Rajesh Bhagat
Signed-off-by: Bhaskar Upadhaya
Signed-off-by: Tang Yuantian
Signed-off-by: Prabhakar Kushwaha