30 Apr, 2012
15 commits
-
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/ppc4xx: Remove typedefs for gdsys FPGA
powerpc/ppc4xx: Fix typo in gdsys_fpga.h
powerpc/ppc4xx: Update gdsys board configurations
powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
powerpc/ppc4xx: Adjust environment size on neo -
* 'master' of git://git.denx.de/u-boot-ppc4xx:
powerpc/ppc4xx: Remove typedefs for gdsys FPGA
powerpc/ppc4xx: Fix typo in gdsys_fpga.h
powerpc/ppc4xx: Update gdsys board configurations
powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
powerpc/ppc4xx: Adjust environment size on neo -
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node -
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node -
* 'master' of /home/wd/git/u-boot/custodians:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734 -
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734 -
Putting "inline" on extern funcs makes no sense, so drop them.
Signed-off-by: Mike Frysinger
-
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc -
Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
In hardware revision 1.20 one more fan controller is added to dlvision-10g.
Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese -
Environment size on neo has to be 0x20000 for compatibilty reasons.
Signed-off-by: Dirk Eibach
Cc: Stefan Roese
Signed-off-by: Stefan Roese
29 Apr, 2012
2 commits
-
md5.c: In function ‘MD5Final’:
md5.c:156:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
md5.c:157:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]Signed-off-by: Marek Vasut
Cc: Wolfgang Denk
Acked-by: Mike Frysinger -
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
CMD: Remove CMD_LOG, it's unused
CMD: Fix typo KGBD -> KGDB on debris board
CMD: Drop CONFIG_CMD_EMMC, it's not used
CMD: Drop CONFIG_CMD_DFL, it's not used
CMD: Drop CMD_DCR, it's not used
CMD: Drop CMD_CAN, it's not used
CMD: Remove CMD_AUTOSCRIPT, it's not used
AT91: Drop AT91_SPIMUX command from cmd_all
25 Apr, 2012
10 commits
-
For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller.
Therefore, the SATA driver will use sata_sil, instead sata_sil3114.Signed-off-by: Jerry Huang
CC: Andy Fleming -
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.Signed-off-by: Liu Gang
Signed-off-by: Shaohui Xie -
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.Signed-off-by: Liu Gang
Signed-off-by: Shaohui Xie -
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.Signed-off-by: Liu Gang
Signed-off-by: Shaohui Xie -
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
locally.For the slave module, need to finish these processes:
1. Set the boot location to SRIO1 or SRIO2 by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
4. Slave's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_SLAVE_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.Signed-off-by: Liu Gang
Signed-off-by: Shaohui Xie -
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.Signed-off-by: Liu Gang
Signed-off-by: Shaohui Xie -
When defined CONFIG_ENV_IS_NOWHERE, there will be some
compilation errors:./common/env_nowhere.o: In function `env_relocate_spec':
./common/env_nowhere.c:38: multiple definition of `env_relocate_spec'
./common/env_flash.o: ./common/env_flash.c:326: first defined here
./common/env_nowhere.o: In function `env_get_char_spec':
./common/env_nowhere.c:42: multiple definition of `env_get_char_spec'
./common/env_flash.o:./common/env_flash.c:78: first defined here
./common/env_nowhere.o: In function `env_init':
./common/env_nowhere.c:51: multiple definition of `env_init'
./common/env_flash.o:./common/env_flash.c:237: first defined here
make[1]: *** [./common/libcommon.o] Error 1
make[1]: Leaving directory `./common'
make: *** [./common/libcommon.o] Error 2Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE.
Signed-off-by: Liu Gang
-
Add env in NAND support when boot from NAND.
Signed-off-by: Shaohui Xie
Signed-off-by: Andy Fleming -
New P2041RDB board will add a NAND chip, so add support for NAND and
NAND boot.Signed-off-by: Shaohui Xie
Signed-off-by: Andy Fleming -
P1010RDB and p1_pc_rdb_pc has incorrect configuration for
CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING.
Incorrect setting causes DDR failure in case of SPD absent.Signed-off-by: York Sun
Signed-off-by: Andy Fleming
24 Apr, 2012
1 commit
-
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platformsThe driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platformsSigned-off-by: Vipin Kumar
Signed-off-by: Amit Virdi
22 Apr, 2012
1 commit
-
board:
Add config file of board adp-ag102
Add adp-ag102 into boards.cfg
Add adp-ag102 into MAINTAINERSdoc:
add README of ag102Signed-off-by: Macpaul Lin
21 Apr, 2012
1 commit
-
Signed-off-by: Jens Scharsig
20 Apr, 2012
10 commits
-
Signed-off-by: Marek Vasut
Acked-by: Anatolij Gustschin -
Fix typo
Signed-off-by: Marek Vasut
Cc: Kyle.D.Moffett@boeing.com
Acked-by: Anatolij Gustschin -
$ git grep CMD_LOG
include/configs/kilauea.h:#define CONFIG_CMD_LOG
include/configs/lwmon5.h:#define CONFIG_CMD_LOG
include/configs/makalu.h:#define CONFIG_CMD_LOG
include/configs/quad100hd.h:#undef CONFIG_CMD_LOG
include/configs/zeus.h:#define CONFIG_CMD_LOGSigned-off-by: Marek Vasut
Acked-by: Anatolij Gustschin -
Signed-off-by: Marek Vasut
Cc: dogoil@etinsys.com
Acked-by: Anatolij Gustschin -
$ git grep CMD_EMMC
include/configs/u8500_href.h:#define CONFIG_CMD_EMMCSigned-off-by: Marek Vasut
Cc: dirk.behme@googlemail.com
Cc: helmut.raiger@hale.at
Cc: john.rigby@linaro.org
Cc: vapier@gentoo.org -
$ git grep CMD_DFL
board/atc/ti113x.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/atc/ti113x.c: pci_writew (s, PCI_COMMAND, CMD_DFLT);
board/cpc45/pd67290.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/cpc45/pd67290.c: pci_writew (s, PCI_COMMAND, CMD_DFLT);
drivers/pcmcia/i82365.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
drivers/pcmcia/i82365.c: pci_writew (s, PCI_COMMAND, CMD_DFLT);
include/configs/MBX.h:#define CONFIG_CMD_DFL
include/configs/MigoR.h:#define CONFIG_CMD_DFL
include/configs/digsy_mtc.h:#define CONFIG_CMD_DFL
include/configs/ms7722se.h:#define CONFIG_CMD_DFL
include/configs/ms7750se.h:#define CONFIG_CMD_DFL
include/configs/r2dplus.h:#define CONFIG_CMD_DFL
include/configs/sh7757lcr.h:#define CONFIG_CMD_DFL
include/configs/sh7785lcr.h:#define CONFIG_CMD_DFLSigned-off-by: Marek Vasut
Cc: Pfister_Werner@intercontrol.de
Cc: iwamatsu@nigauri.org
Cc: nobuhiro.iwamatsu.yj@renesas.com
Cc: vapier@gentoo.org
Cc: wd@denx.de
Cc: yoshihiro.shimoda.uh@renesas.com
Acked-by: Anatolij Gustschin
Acked-by: Nobuhiro Iwamatsu -
$ git grep CMD_DCR
include/configs/ep8260.h:#undef CONFIG_CMD_DCRSigned-off-by: Marek Vasut
Acked-by: Anatolij Gustschin -
$ git grep CMD_CAN
include/configs/jadecpu.h:#define CONFIG_CMD_CANSigned-off-by: Marek Vasut
Cc: Matthias Weisser -
$ git grep AUTOSCRIPT
include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT
include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPTSigned-off-by: Marek Vasut
Cc: Albert ARIBAUD
Cc: Prafulla Wadaskar
Acked-by: Anatolij Gustschin -
$ git grep AT91_SPIMUX
include/config_cmd_all.h:#define CONFIG_CMD_AT91_SPIMUX /* AT91 MMC/SPI Mux Support */It isn't used anywhere it seems.
Signed-off-by: Marek Vasut
Cc: Albert ARIBAUD
Acked-by: Anatolij Gustschin