07 Sep, 2015
4 commits
-
dfu-util allows filtering on USB device vendor:product ID by using
the -d flag (-d 0451:d022).
Such option is very handy when many DFU devices are connected to a single
host PC. This commit allows testing when above situation emerges.Signed-off-by: Lukasz Majewski
Reviewed-by: Simon GlassTested-by: Lukasz Majewski
Test HW - AM335x Beagle Bone Black
NOTE: Max size of file to transfer: 2MiB -
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek -
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.The case would be to download the images to DDR instead
of flash device.Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek -
Signed-off-by: Jiandong Zheng
Signed-off-by: Steve Rae
04 Sep, 2015
3 commits
-
Signed-off-by: Stefan Brüns
-
The default config includes base.menu, not linux.list
Signed-off-by: Stefan Brüns
03 Sep, 2015
33 commits
-
It is easier to paste these into the command line if they are a single
common. Use line continuation instead of separate lines.Signed-off-by: Simon Glass
-
MMC support works now, so it can be dropped from the todo
Signed-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
Instead of creating a rockchip SPL SD card image with 32KB of zeros
which can be written to the start of an SD card, create the images with
only the useful data that should be written to an offset of 32KB on the
SD card.The first 32 kilobytes aren't needed for bootup and only serve as
convenient way of accidentally obliterating your partition table.Signed-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.Signed-off-by: Sjoerd Simons
Reviewed-by: Simon Glass
Signed-off-by: Simon Glass -
Now that MMC works in U-Boot add config distro command support to start
Linux in a standard fashion. One oddity here is that linux fails to load
when the fdt is relocated to above 512MB, so set fdt_high to make sure it's
loaded below that.Signed-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
With LED support enabled the SPL easily goes over the size limit (e.g.
with both Debians gcc 4.9 and 5.2 cross-compilers). Turn off LED support
in the SPL to reduce the size just enough for those compilers.Signed-off-by: Sjoerd Simons
Tweaked commit subject to remove _SUPPORT
Signed-off-by: Simon Glass -
U-Boot can't use the sdio card so turn it of to prevent things getting
confused/struck when trying to use the card as storage.Signed-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
During mmc initialize probe all devices with the MMC Uclass if build
with CONFIG_DM_MMCSigned-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
The Radxa Rock pro board is rk3188 based and thus won't work with U-Boot
built for RK3288. Change the documentation to refer to the intended
board, the Radxa Rock 2, which is an RK3288-based design very similar to
the fireflySigned-off-by: Sjoerd Simons
Acked-by: Simon Glass
Signed-off-by: Simon Glass -
Add a few notes on how to try out the Rockchip support so far.
Signed-off-by: Simon Glass
-
This builds and displays an SPL message, but does not function beyond that.
Signed-off-by: Simon Glass
-
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.Signed-off-by: Simon Glass
-
Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.Signed-off-by: Simon Glass
-
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.Signed-off-by: Simon Glass
-
Add code for starting up U-Boot SPL and U-Boot proper. This is generic and
makes use of devices provided by the board- or SoC-specific code.Signed-off-by: Simon Glass
-
Add an MMC driver which supports RK3288, but may also support other SoCs.
It uses the Designware MMC device.Signed-off-by: Simon Glass
-
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.Signed-off-by: Simon Glass
-
Add a driver which supports pin multiplexing setup for the most commonly
used peripherals.Signed-off-by: Simon Glass
-
Add a driver that provides access to system controllers.
Signed-off-by: Simon Glass
-
We can reset the SoC using some CRU (clock/reset unit) registers. Add support
for this.Signed-off-by: Simon Glass
-
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.Signed-off-by: Simon Glass
-
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3288.Signed-off-by: Simon Glass
-
Add a full regulator driver for the ACT8846. This provides easy access to
voltage and current settings for each regulator.Signed-off-by: Simon Glass
-
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.Signed-off-by: Simon Glass
-
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.Signed-off-by: Simon Glass
-
This supports RK3288 at present. It does not implement functions or support
for pull up/down.Signed-off-by: Simon Glass
-
The Rockchip boot ROM requires a particular file format for booting from SPI.
It consists of a 512-byte header encoded with RC4, some padding and then up
to 32KB of executable code in 2KB blocks, separated by 2KB empty blocks.Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format. This allows booting from SPI flash on supported
machines.Signed-off-by: Simon Glass
-
The Rockchip boot ROM requires a particular file format. It consists of
64KB of zeroes, a 512-byte header encoded with RC4, and then some executable
code.Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format.Signed-off-by: Simon Glass
-
Rockchip SoCs require certain formats for code that they execute, The
simplest format is a 4-byte header at the start of a binary file. Add
support for this so that we can create images that the boot ROM understands.Signed-off-by: Simon Glass
-
Allow the image handler to store the original input file size so that it
can reference it later.Signed-off-by: Simon Glass
Reviewed-by: Joe Hershberger -
At present there is an arbitrary limit of 4KB for padding. Rockchip needs
more than that, so remove this restriction.Signed-off-by: Simon Glass
Reviewed-by: Joe Hershberger -
In SPL we need access to the CRU and other peripherals so we can set up
SDRAM. Mark these so that they will remain in the device tree.Signed-off-by: Simon Glass
-
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.Signed-off-by: Simon Glass
