04 Mar, 2016
40 commits
-
Imported the picosom boot codes and board
configs from technexion.Signed-off-by: Tapani Utriainen
Signed-off-by: Haoran Wang -
Define CONFIG_SYS_VSNPRINTF to use snprintf, but not sprintf.
Coverity ID: 17926.Signed-off-by: Peng Fan
-
We support max 16 endpoints, but endpoint starts from 0.
So we need to use >= 16 but not > 16 to check whether we
already reach max endpoints or not.Coverity ID 17955:
Out-of-bounds read (OVERRUN)
37. overrun-local: Overrunning array dev->config.if_desc[ifno].ep_desc of 16
9-byte elements at element index 16 (byte offset 144) using index epno
(which evaluates to 16).Signed-off-by: Peng Fan
-
We should use ARRAY_SIZE, but not directly sizeof, otherwise
we may access memory that is not belong the array env_flags_varaccess_mask.Coverity ID: 17949
Signed-off-by: Peng Fan
-
Report Coverity log:
Destination buffer too small (STRING_OVERFLOW)
string_overflow: You might overrun the 1024 byte destination string
lastcommand by writing 1025 bytes from console_bufferSigned-off-by: Peng Fan
-
Reported by coverity ID: 17900 17902
Using uninitialized value e. Field e.flags is uninitialized when calling hsearch_rSigned-off-by: Peng Fan
-
The list_first_entry always assumes the list is not empty, it won't return NULL pointer when
the list is empty. So the "if (pdesc == NULL)" becomes a dead code. Fix the issue by calling
the list_empty before the list_first_entry.(Coverity CID 29934)
Signed-off-by: Ye.Li
-
Fix a read from pointer after free issue in nand error handling path,
which was found by coverity.Signed-off-by: Han Xu
-
unsigned long long data might have strange data if first bit of u8 data
was 1. this patch cast it to (unsigned long long)ex)
u8 data8;
u64 data64;data8 = 0x80;
data64 = (data8 << 24); // 0xffffffff80000000
data64 = (((unsigned long long)data8) << 24); // 0x80000000;(reported by Coverity)
Signed-off-by: Haibo Chen
-
Before calling hsearch_r, initialize callback entry to NULL.
Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"Reported-by: Coverity
Signed-off-by: Peng Fan
Cc: Tom Rini
Cc: Simon Glass
(cherry picked from commit 5a6894397a657edec5d0cf4e20968cc66a368c51) -
Use snprintf to replace sprintf.
Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"Reported-by: Coverity
Signed-off-by: Peng Fan
Cc: Tom Rini
Cc: Simon Glass
Reviewed-by: Joe Hershberger
(cherry picked from commit 5d49b4cdf9417b88476567c8ec78ff185d84b10f) -
Whether CONFIG_SYS_HUSH_PARSER is defined or not, should always
check to free 'buff' to avoid memory leak.Signed-off-by: Peng Fan
Cc: Tom Rini
Cc: Masahiro Yamada
Cc: Simon Glass
(cherry picked from commit 09a788624dbe32aeeb0d74c97c0965303eb96d8c) -
The latest iomux head file generated by tool has added some new pinmux settings. Update the
mx6ul_pins.h to this version.Signed-off-by: Ye.Li
-
Need to free memory avoid memory leak, when error.
Signed-off-by: Peng Fan
Reviewed-by: Simon Glass
Cc: Simon Glass
Cc: Tom Rini
(cherry picked from commit c6bb23c819b5dcbc5c3491673f5e408c0b9c38b3) -
The following code will alloc memory for new_dev and ldev:
"
new_dev = mdio_alloc();
ldev = malloc(sizeof(*ldev));
"
Either new_dev or ldev is NULL, directly return, but this may leak memory.
So before return, using free(ldev) and mdio_free(new_dev) to avoid
leaking memory, also free can handle NULL pointer.Signed-off-by: Peng Fan
Cc: Joe Hershberger
Cc: Simon Glass
Cc: Bin Meng
Reviewed-by: Bin Meng
Acked-by: Joe Hershberger
(cherry picked from commit 746da1bd42aa5ecc47898399514c9c76d0329706) -
"enable" is unsigned char type and its value will not be
negative, so discard "enable < 0".Signed-off-by: Peng Fan
Cc: Diego Santa Cruz
Cc: Pantelis Antoniou
Cc: Andrew Gabbasov
Cc: Simon Glass
Cc: Stefano Babic
Cc: Tom Rini
Reviewed-by: Simon Glass
(cherry picked from commit 678e9316d48f78d162f705846b6f6eeab4aa5dd0) -
The entry name of mii_dev is an array not pointer, so
no need to check.Signed-off-by: Peng Fan
Cc: Joe Hershberger
Cc: Simon Glass
Cc: Bin Meng
Reviewed-by: Simon Glass
Acked-by: Joe Hershberger
Reviewed-by: Bin Meng
(cherry picked from commit d39449b110c8da47bf5b8dc372bd5cd1c33a1a67) -
If condition of "(load == image_start || load == image_data)" is true,
should use "fdt_addr = load;", but not "fdt_blob = (char *)image_data;",
or fdt_blob will be overridden by "fdt_blob = map_sysmem(fdt_addr, 0);"
at the end of the switch case.Signed-off-by: Peng Fan
Cc: Simon Glass
Cc: Joe Hershberger
Cc: Max Krummenacher
Cc: Marek Vasut
Cc: Suriyan Ramasami
Cc: Paul Kocialkowski
Cc: Tom Rini
Reviewed-by: Simon Glass
(cherry picked from commit 2ea47be02f356ff275fa5c50392ea510ddb4a96c) -
Condition "(value == NULL && ++value == NULL)" actully will
always return false.Instead, use condition "(value == NULL || *(value + 1) == 0)" to detect
such expression "c=". To "c=", *(value + 1) is 0, so directly return -1,
but not continue.Signed-off-by: Peng Fan
Cc: Rabin Vincent
Cc: Simon Glass
Cc: Tom Rini
Reviewed-by: Simon Glass
(cherry picked from commit aa722529635c16c52d9d609122fecc96ec8d03e4) -
Before continue, check return value of strict_strtoul.
Signed-off-by: Peng Fan
Cc: Albert Aribaud
Cc: Simon Glass
Cc: Jan Kiszka
Cc: Joe Hershberger
Cc: Hans de Goede
Cc: York Sun
Cc: Tom Rini
Reviewed-by: Simon Glass
(cherry picked from commit bc3c89b1308281edceb67051a44026545dc7b505) -
Currently there is no API to uninitialize mdio. Add two APIs for this.
Signed-off-by: Bin Meng
Acked-by: Joe Hershberger
(cherry picked from commit cb6baca77bca0ef999203a7ed73bd123e7da062e) -
Introudce wp_enable. If want to check WPSPL, then in board code,
need to set wp_enable to 1.Take i.MX6UL for example, to some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.Suggested-by: Ye.Li
Signed-off-by: Peng Fan -
There is a bad dhcp server which always gives board ipaddr 0.0.0.0,
and board can not get ipaddr from correct dhcp server, since the bad
dhcp server always reply the board's dhcp packet with bad address.
We can ignore the bad dhcp server by checking the assigned ipaddr,
checking whether it is 0 or not.Signed-off-by: Peng Fan
-
Fix mmdc_ch0 clk calculation. Also add PLL_AUDIO/VIDEO support
for decode_pll.Reported-by: Bai Ping
Signed-off-by: Peng Fan -
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.Signed-off-by: Peng Fan
-
Add mx6qarm2 new board revision support using mx6q pop SoC
Enable DRAM support for imx6q PoP SoC with populated LPDDR2
MT42L128M64D2DDR calibration script
http://sw-stash.freescale.net/projects/IMX/repos/ddr-scripts-rel/commits/e5c6184940486bcbc28978d60ad3cd996c205a08
Test result: Stress test passed.Signed-off-by: Adrian Alonso
-
Since i.MX7D SDB revB board has some HW changes, we have modify the BSP file to support new pinmux.
1. OTG2 PWR pin is changed to GPIO1_IO07.
2. A enet2_en pin is added for isolating enet2 signals with EPDC, we also add support for enet2.
3. pin6 of 74LV output is changed for CSI PWDN. Set output to high to power down it.This patch also tries to get the board id and apply changes according with it. Since current
RevB board does not burn GP1 fuse for board id, we have to check the TO rev instead even it is not very
exact. Will update this if any new way implemented.Signed-off-by: Ye.Li
-
Current Micron DDR MT41K256M16HA-125 on i.MX6UL will be EOL. Plan is i.MX6UL
will use the new 20nm litho 4Gb DDR3L MT41K256M16TW-107.Update DDR script of mx6ul evk board for this new DDR, and use it as default.
http://compass.freescale.net/livelink/livelink?func=ll&objId=234910940&objAction=browse&viewType=1Test result:
Stress test passed.Meanwhile add build targets below for old DDR support:
mx6ul_14x14_evk_ddr_eol_android_defconfig
mx6ul_14x14_evk_ddr_eol_brillo_defconfig
mx6ul_14x14_evk_ddr_eol_defconfig
mx6ul_14x14_evk_ddr_eol_qspi1_defconfigSigned-off-by: Ye.Li
-
We can rely on finish bit for temperature reading for TO1.1.
Also introduce CHIP_REV_xx macros for 7D.Signed-off-by: Peng Fan
-
i.MX7D TO1.1 changes DDR retension mode control to IOMUXC_GPR,
add support to this change for LPSR which needs to exit from
DDR retension mode.Signed-off-by: Anson Huang
-
Clear DLL_CTRL delay line settings at USDHC initialization to eliminate the
pre-settings from boot rom. U-boot should re-init the USDHC not reply on the
value set by boot from.On MX6DL, the ROM has set the default delay line(DLLCTRL) to 0x1000021,
when eMMC works on DDR mode in kernel, it will possibly cause data CRC errors.
Even u-boot always use eMMC in SDR mode, for safety sake, it is better to clear it too.Signed-off-by: Ye.Li
-
change the imx7d arm2 nand rootfs partition index from 3 to 4 since the
weim nor was enabled by default and took the first mtd partition.Signed-off-by: Han Xu
-
By Coverity check, the clk_set_rate function dereferences the clk pointer
without checking whether it is NULL. This may cause problem when clk is NULL.
Fix the problem by adding NULL check.Signed-off-by: Ye.Li
-
According to the Coverity result, a unsigned int variable is used fo less-
than-zero comparison, the result is never true. Need to fix the variable
type to signed int.Signed-off-by: Ye.Li
-
uboot will fail when loader zImage which is larger than 9M.
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB.Signed-off-by: Zhang Sanshan
-
Android's tool chain enable the -mandroid at default.
This option will enable the -fpic, which cause uboot compilation
failure:
"
LD u-boot
u-boot contains unexpected relocations: R_ARM_ABS32
R_ARM_RELATIVE
"In my testcase, arm-linux-androideabi-gcc-4.9 internally
enables '-fpic', so when compiling code, there will be
relocation entries using type R_ARM_GOT_BREL and .got
section. When linking all the built-in.o using ld, there
will be R_ARM_ABS32 relocation entry and .got section
in the final u-boot elf image. This can not be handled
by u-boot, since u-boot only expects R_ARM_RELATIVE
relocation entry.
arm-poky-linux-gnueabi-gcc-4.9 default does not enable '-fpic',
so there is not .got section and R_ARM_GOT_BREL in built-in.o.
And in the final u-boot elf image, all relocation entries are
R_ARM_RELATIVE.we can pass '-fno-pic' to xxx-gcc to disable pic. whether
the toolchain internally enables or disables pic, '-fno-pic'
can work well.Signed-off-by: Peng Fan
-
We need to access reg stp_rep9, but not stp_rep[(9 - 1) / 2].
If using "__raw_writel(0, DI_STP_REP(disp, 9))", this will exceeds
the size of stp_rep array.Acked-by: Liu Ying
Signed-off-by: Peng Fan -
ret should not use unsigned integer. Should use signed interger to
compare against 0.Signed-off-by: Peng Fan
-
birllo use gcc-4.9 to compile kernel, zImage is large then 8M.
set CONFIG_SYS_BOOTM_LEN to 16MSigned-off-by: fang hui
Conflicts:
include/configs/mx6ul_14x14_evk_brillo.h -
This reverts commit 24356fe059abbc9eae1b192f7af8a46f204a36f4.
Conflicts:
common/image-android.cConflicts:
common/image-android.c