01 Jun, 2017
8 commits
-
Sometimes it is useful to be able to find a block device without also
probing it. Add a function for this as well as the associated test.Signed-off-by: Simon Glass
-
With live tree we need a struct device_node * to reference a node. With
the existing flat tree, we need an int offset. We need to unify these into
a single value which can represent both.Add an ofnode union for this and adjust existing code to move to this.
Signed-off-by: Simon Glass
-
This function is only used in one place. It is better to just declare it
internally since there is a simpler replacement for use outside the
driver-model core code.Signed-off-by: Simon Glass
-
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree onlyAll drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass
-
Move this group of address-related functions into a new file. These use
the flat device tree. Future work will provide new versions of these which
can support the live tree.Signed-off-by: Simon Glass
-
Please pull another update for Broadcom MIPS.
This contains new SoC's, new boards and new drivers and some bugfixes. -
Mostly including the Armada 37xx pinctrl / gpio driver.
-
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.Signed-off-by: Daniel Thompson
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini
31 May, 2017
8 commits
-
Now that the uart driver has been fixed we support more baud rates.
Signed-off-by: Álvaro Fernández Rojas
-
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Signed-off-by: Álvaro Fernández Rojas
Reviewed-by: Simon Glass -
Switch Clearfog to the generic distro defaults. This has been taken
from a Debian mailing list thread:https://lists.debian.org/debian-boot/2016/10/msg00026.html
Signed-off-by: Patrick Wildt
Signed-off-by: Stefan Roese
29 May, 2017
2 commits
-
Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf
Signed-off-by: Keerthy
Fixes: 86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung -
In some places we check if part_config is set to MMCPART_NOAVAILABLE
(0xff). With part_config being a char this is always false. We should
be using a u8 to store this value instead, after a quick consultation
with the Linux Kernel. Reported by clang-3.8.Cc: Jaehoon Chung
Signed-off-by: Tom Rini
26 May, 2017
2 commits
-
Move FTMAC100 to where it should be, alphabetically in
drivers/net/KconfigSigned-off-by: Tom Rini
Conflicts:
drivers/net/Kconfig
24 May, 2017
13 commits
-
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.Signed-off-by: Udit Agarwal
Reviewed-by: York Sun -
This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as belowImage Flash Offset
RCW+PBI 0x00000000
Boot firmware (U-Boot) 0x00100000
Boot firmware Environment 0x00300000
PPA firmware 0x00400000
PHY firmware 0x00980000
DPAA2 MC 0x00A00000
DPAA2 DPL 0x00D00000
DPAA2 DPC 0x00E00000
Kernel.itb 0x01000000Signed-off-by: Santan Kumar
Signed-off-by: Priyanka Jain
Reviewed-by: York Sun -
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.Signed-off-by: Alison Wang
Reviewed-by: York Sun -
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.Signed-off-by: Alison Wang
Reviewed-by: York Sun -
This patch is to adjust the memory mapping for FLash/SD card on
LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial
Flash, QE firmware load address and environment address.Signed-off-by: Alison Wang
Reviewed-by: York Sun -
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2CSigned-off-by: Priyanka Jain
Signed-off-by: Santan Kumar
Reviewed-by: York Sun -
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.Signed-off-by: Priyanka Jain
Signed-off-by: Suresh Gupta
Reviewed-by: York Sun -
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun
CC: Mingkai Hu
Acked-by: Mingkai Hu -
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun
CC: Mingkai Hu
Acked-by: Mingkai Hu -
LS1012AFRDM, LS1012ARDB, LS1012AQDS all have S25FS512S flash
of 64MB size.Signed-off-by: Suresh Gupta
-
ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does
not support Bank Address Register commands.Signed-off-by: Suresh Gupta
Reviewed-by: York Sun -
Signed-off-by: Hou Zhiqiang
Reviewed-by: York Sun
23 May, 2017
7 commits
-
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4899 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'boomimage-310y-ae300-spi.bin'.
Load address: 0x600000
Loading: #################################################################
#################################################################
#################################################################
...
...
###################################
233.4 KiB/s
done
Bytes transferred = 13872076 (d3abcc hex)
NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4592 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'ae300.dtb'.
Load address: 0x2000000
Loading: #
82 KiB/s
done
Bytes transferred = 2378 (94a hex)
NDS32 # bootm 0x600000 - 0x2000000
Image Name:
Created: 2017-03-22 6:52:03 UTC
Image Type: NDS32 Linux Kernel Image (uncompressed)
Data Size: 13872012 Bytes = 13.2 MiB
Load Address: 0000c000
Entry Point: 0000c000
Verifying Checksum ... OK
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to 01efc000, end 01eff949 ... OK
Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
#293 PREEMPT Wed Mar 22 14:49:28 CST 2017
CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick -
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).Signed-off-by: Tom Rini
-
The original commit for the MCF54418TWR ColdFire development board
support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN'
which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the
intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define.Signed-off-by: Lothar Waßmann
-
This converts the following to Kconfig:
CONFIG_CMD_LZMADECSigned-off-by: Simon Glass
-
This converts the following to Kconfig:
CONFIG_LZMASigned-off-by: Simon Glass
-
This is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass
