10 Apr, 2015
2 commits
-
At present Hyungwon can't take care of this board in U-Boot,
so I will keep it working.Signed-off-by: Przemyslaw Marczak
Cc: Hyungwon Hwang -
Remove obsolete email address from MAINTAINERS.
Signed-off-by: Anatolij Gustschin
Cc: Masahiro Yamada
Cc: Tom Rini
09 Apr, 2015
1 commit
-
Email address is not longer valid that's why remove it.
Signed-off-by: Michal Simek
06 Apr, 2015
1 commit
-
Remove GPIOs from smdk5420 board file and because the same
is already specified via DT.Signed-off-by: Ajay Kumar
Reviewed-by: Simon Glass
Tested-by: Simon Glass
Signed-off-by: Minkyu Kang
03 Apr, 2015
3 commits
-
Conflicts:
board/armltd/vexpress64/vexpress64.cSigned-off-by: Tom Rini
-
With the most recent board firmware correct SDIO clock is 50MHz as
opposed to 25 MHz before.Also set max frequency of MMC data exchange equal to SDIO clock -
because there's no way to transfer data faster than interface clock.Signed-off-by: Alexey Brodkin
01 Apr, 2015
6 commits
-
Enable SPL support for at91sam9n12ek boards, now it supports
boot up from NAND flash, serial flash.Signed-off-by: Bo Shen
-
Enable SPL support for at91sam9x5ek board. Now, it supports
boot up from NAND flash and SPI flash.Signed-off-by: Bo Shen
-
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.Signed-off-by: Bo Shen
-
This patch will display the U-Boot version on LCD.
Signed-off-by: Josh Wu
Acked-by: Bo Shen
31 Mar, 2015
7 commits
-
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.Signed-off-by: Peter Tyser
Tested-by: Heiko Schocher
Acked-by: Heiko Schocher -
Pingroup ATC seems to come out of reset with config set to NAND, so we
need to explicitly configure some other function to this group in order
to avoid clashing settings.Signed-off-by: Marcel Ziswiler
Signed-off-by: Tom Warren -
Fix ASIX USB to Ethernet chip reset.
Signed-off-by: Marcel Ziswiler
Acked-by: Stephen Warren
Signed-off-by: Tom Warren -
In accordance with our other modules supported by U-Boot and as agreed
upon for Apalis/Colibri T30 get rid of the carrier board in the board/
configuration/device-tree naming.While at it also bring the prompt more in line with our other products.
Signed-off-by: Marcel Ziswiler
Signed-off-by: Tom Warren -
As a preparatory step to renaming the board folder as well first get
rid of the colibri_t20-common after having integrated it into
colibri_t20_iris for now.While at it also migrate to using NVIDIA's common.mk magic.
Signed-off-by: Marcel Ziswiler
Signed-off-by: Tom Warren -
Requesting a GPIO without a name is not supposed anymore. This causes the
request to fail. Add a name so that the serial console works on seaboard.Signed-off-by: Simon Glass
Reported-by: Stephen Warren
Signed-off-by: Tom Warren
29 Mar, 2015
8 commits
-
Signed-off-by: Hans de Goede
-
make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on bootSigned-off-by: Iain Paton
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede
Signed-off-by: Hans de Goede -
Add CONFIG_SYS_GENERIC_BOARD to amcc-common.h and CONFIG_DISPLAY_BOARDINFO
to Kconfig files. canyonlands.h includes amcc-common.h, so remove
CONFIG_SYS_GENERIC_BOARD definition there.Signed-off-by: Anatolij Gustschin
Cc: Stefan Roese
Cc: Feng Kan
Cc: Masahiro Yamada
Cc: Tom Rini -
Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error.
These boards have video but don't need any ppc related
video_setmem().Fix M53017EVB moving away embedded env to a different offset,
as in M52277EVB.Signed-off-by: Angelo Dureghello
-
This variant that is neither FVP / Base Model or Juno Versatile
Express 64bit is confusing. Get rid of it unless someone can
point out what machine that really is. Seems to be an evolutional
artifact in the config base.Signed-off-by: Linus Walleij
-
This removes the kludgy late board init from the FVP simulator
version of Versatile Express 64bit (ARMv8), and replace it with
a default boot command using the new smhload command to load
the files using semihosting. Tested on the Foundation Model.Signed-off-by: Linus Walleij
-
since we have possibility to write out on lcd whats going on, we don't need
the gpio blink functionality anymore.Signed-off-by: Hannes Petermaier
Signed-off-by: Hannes Petermaier
-
At this time I2C and responsible pin-mux is setup during PMIC initialziation
within common.c, this is possible because today PMIC is always connected on
I2C0.In Future this will be changed, PMIC isn't anymore connected to bus0 in call
cases.So we do following:
- rename enable_i2c_pin_mux0 to enable_i2c_pin_mux to be generic for enabling
pin-mux on different or more busses.
- move the call to i2c_pin_mux and i2c_init from common.c to the specific
board.cSigned-off-by: Hannes Petermaier
Signed-off-by: Hannes Petermaier
28 Mar, 2015
3 commits
-
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough. One of the biggest differences is the ARM
processor. It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.Signed-off-by: Masahiro Yamada
Acked-by: Stephen Warren -
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.Signed-off-by: Masahiro Yamada
Acked-by: Stephen Warren
Reviewed-by: Simon Glass
Acked-by: Robert Baldyga -
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400. Each defconfig or Kconfig need not repeat the same value.Signed-off-by: Masahiro Yamada
Acked-by: Stephen Warren
Reviewed-by: Simon Glass
Acked-by: Robert Baldyga
27 Mar, 2015
1 commit
-
Signed-off-by: David Feng
24 Mar, 2015
3 commits
-
After v2015.01 we need to have DM enabled in order to use UART. Also
fix a typo in the EEPROM config format.Signed-off-by: Gilles Gameiro
[trini: Reword commit message, re-save defconfigs with 'savedefconfig']
Signed-off-by: Tom Rini -
Apparently the firmware's board rev response includes both the board
revision and some other data even on the RPi1. In particular, the
"warranty bit" is bit 24. We need to mask that out when looking up the
board ID.Signed-off-by: Stephen Warren
-
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.Signed-off-by: Rob Herring
Cc: Albert Aribaud
Cc: Stefano Babic
Cc: Minkyu Kang
Cc: Marek Vasut
Cc: Tom Warren
Cc: Michal Simek
Cc: Macpaul Lin
Cc: Wolfgang Denk
Cc: York Sun
Cc: Stefan Roese
Cc: Nobuhiro Iwamatsu
Cc: Simon Glass
Cc: Philippe Reynes
Cc: Eric Jarrige
Cc: "David Müller"
Cc: Phil Edworthy
Cc: Robert Baldyga
Cc: Torsten Koschorrek
Cc: Anatolij Gustschin
Reviewed-by: Linus Walleij
Reviewed-by: Łukasz Majewski
23 Mar, 2015
1 commit
-
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).Signed-off-by: Boris Brezillon
20 Mar, 2015
1 commit
19 Mar, 2015
2 commits
-
Enable the power for MMC/SD port.
Signed-off-by: Bo Shen
-
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu
[rebase on ToT]
Signed-off-by: Andreas Bießmann
18 Mar, 2015
1 commit