25 Feb, 2014
1 commit
-
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial portsSigned-off-by: Shengzhou Liu
Reviewed-by: York Sun
07 Feb, 2014
2 commits
-
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMACSigned-off-by: Alexey Brodkin
Cc: Vineet Gupta
Cc: Francois Bedard
Cc: Wolfgang Denk
Cc: Heiko Schocher -
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)Signed-off-by: Alexey Brodkin
Cc: Vineet Gupta
Cc: Francois Bedard
Cc: Wolfgang Denk
Cc: Heiko Schocher
04 Feb, 2014
1 commit
-
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.Signed-off-by: Valentin Longchamp
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun
27 Jan, 2014
1 commit
-
Run "tools/reformat.py -i -d '-' -s 8 boards0.cfg && mv boards0.cfg boards.cfg"
in order to keep the entries sorted.Signed-off-by: Fabio Estevam
22 Jan, 2014
2 commits
-
u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.So, Increase the u-boot binary size to 768KB.
Signed-off-by: York Sun
Signed-off-by: Prabhakar Kushwaha -
Using the TPL/SPL method to booting from 8k page NAND flash.
- Add 256kB size SRAM tlb for second step booting;
- Add spl.c for TPL image boot;
- Add spl_minimal.c for minimal SPL image;
- Add C29XPCIE_NAND configure;
- Modify C29XPCIE.h for nand config and enviroment;Signed-off-by: Po Liu
Reviewed-by: York Sun
15 Jan, 2014
2 commits
-
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton .
Signed-off-by: Jon Nettleton
Signed-off-by: Fabio Estevam
14 Jan, 2014
2 commits
-
Signed-off-by: Albert ARIBAUD
Acked-by: Stefano Babic -
Signed-off-by: Albert ARIBAUD
Acked-by: Minkyu Kang
10 Jan, 2014
9 commits
-
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.Conflicts:
include/configs/exynos5250-dt.hSigned-off-by: Tom Rini
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM012:
- 1GB DDR3
- 64MiB Numonyx NOR flash
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
Cc: Stefan Roese -
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM013:
- 1GB DDR3
- 128 Mb Quad-SPI Flash(dual parallel)
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM010:
- 1Gb DDR3
- 1Mb SST SPI flash
- 128 Mb Quad-SPI Flash
- 8 Mb SST SI flash
- Full size SD/MMC card cage
- 10/100/1000 Ethernet
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switchFor more info - http://zedboard.org/product/microzed
Signed-off-by: Jagannadha Sutradharudu Teki
-
Zed is a complete development board based on the
Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z020-CLG484-1
Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash(
- Full size SD/MMC card cage
Connectivity:
- 10/100/1000 Ethernet
- USB OTG (Device/Host/OTG)
- USB-UART
Expansion:
- FMC (Low Pin Count)
- Pmod. headers (2x6)
Video/Display:
- HDMI output (1080p60 + audio)
- VGA connector
- 128 x 32 OLED
- User LEDs (9)
User inputs:
- Slide switches (8)
- Push button switches (7)
Audio:
- 24-bit stereo audio CODEC
- Stereo line in/out
- Headphone
- Microphone input
Analog:
- Xilinx XADC header
- Supports 4 analog inputs
- 2 Differential / 4 Single-ended
Debug:
- On-board USB JTAG programming port
- ARM Debug Access Port (DAP)For more info - http://zedboard.org/product/zedboard
Signed-off-by: Jagannadha Sutradharudu Teki
-
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.ZC702-:
APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDsFor more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htmZC706-:
APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDsFor more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htmSigned-off-by: Jagannadha Sutradharudu Teki
-
zynq.h -> zynq-common.h, zynq-common is Common
configuration options for all Zynq boards.zynq.h is no longer exists hense removed from boards.cfg
Signed-off-by: Jagannadha Sutradharudu Teki
-
The vexpress_aemv8a is the first aarch64 board in U-Boot.
As it was introduced, it gets built when "MAKEALL -a arm"
is invoked, and fails as this command is run with a 32-bit,
not 64-bit, toolchain as the cross-compiler.Introduce 'aarch64' as a valid 'MAKEALL -a' argument, treated
as 'arm' for all other intents, and change the architecture
of the vexpress_aemv8a entry in boards.cfg from 'arm' to
'aarch64'.
09 Jan, 2014
2 commits
-
Signed-off-by: David Feng
Signed-off-by: Bhupesh Sharma
08 Jan, 2014
1 commit
-
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.Signed-off-by: Tom Rini
07 Jan, 2014
1 commit
06 Jan, 2014
3 commits
-
The board is similar to the standard km_kirkwood board. From a
u-boot point of view, the only difference is an increased
256 MiB DRAM (128M16). A board based on this design is for
example the SUP12.Signed-off-by: Karlheinz Jerg
Signed-off-by: Holger Brunck -
Conflicts:
include/micrel.hThe conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
03 Jan, 2014
1 commit
-
Signed-off-by: Shaohui Xie
30 Dec, 2013
1 commit
-
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.Signed-off-by: Rajeshwari S Shinde
Signed-off-by: Akshay Saraswat
Acked-by: Simon Glass
Signed-off-by: Minkyu Kang
21 Dec, 2013
1 commit
-
With changes to the rtl8169 ethernet to improve cache support, we have
needed additional cache functions for mpc8245. As the board maintainer
has been unresponsive, remove this board.Cc: Guennadi Liakhovetski
Signed-off-by: Tom Rini
20 Dec, 2013
1 commit
-
Update boards.cfg entries for Samsung's GONI and Universal_C210 maintainers
entry.Signed-off-by: Lukasz Majewski
Acked-by: Minkyu Kang
19 Dec, 2013
3 commits
-
Adding Maintainer for AM43xx.
Signed-off-by: Lokesh Vutla
-
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.Signed-off-by: Alban Bedel
Reviewed-by: Stephen Warren
Signed-off-by: Tom Warren -
I no longer work for Avionic Design and don't have access to hardware,
so I'll pass on maintainership to Alban.Acked-by: Alban Bedel
Signed-off-by: Thierry Reding
Signed-off-by: Tom Warren
18 Dec, 2013
1 commit
-
The SH7753 EVB board has SH7753, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.This patch support the following functions:
- 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMCSigned-off-by: Yoshihiro Shimoda
Signed-off-by: Nobuhiro Iwamatsu
13 Dec, 2013
2 commits
-
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.Signed-off-by: Stefan Roese
Cc: Tapani Utriainen
Cc: Thorsten Eisbein
Cc: Tom Rini -
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.Signed-off-by: Tapani Utriainen
CC: Sandeep Paulraj
Signed-off-by: Stefan Roese
Cc: Thorsten Eisbein
Cc: Tom Rini
11 Dec, 2013
1 commit
-
Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyardNeeded manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds
09 Dec, 2013
2 commits
-
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.Signed-off-by: Mateusz Kulikowski
Signed-off-by: Andreas Bießmann -
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt
Reviewed-by: Heiko Schocher
Cc: Andreas Bießmann
Cc: Bo Shen
Signed-off-by: Andreas Bießmann
