24 Feb, 2014
1 commit
-
Run "tools/reformat.py -i -d '-' -s 8 boards0.cfg && mv boards0.cfg boards.cfg"
in order to keep arc entries sorted.Signed-off-by: Fabio Estevam
22 Feb, 2014
2 commits
-
There are some entries which produce the same binaries:
- ep8248E is equivalent to ep8248
- MPC8360ERDK_66 is equivalent to MPC8360ERDK
- Adder87x/AdderUSB is equivalent to Adder
- EVB64260_750CX is equivalent to EVB64260I also notice
- Lite5200 is equivalent to icecube_5200
- Lite5200_LOWBOOT is equivalent to icecube_5200_LOWBOOT
- Lite5200_LOWBOOT08 is equivalent to icecube_5200_LOWBOOT08
But I am keeping them.
(Wolfgang suggested to do so because Lite5200* are referenced
in misc documents.)Signed-off-by: Masahiro Yamada
-
The 8th field of boards.cfg takes the form:
[:comma separated config options]We should describe explicitely the 8th field only when it is necessary
to do so.
Specify "-" in the 8th field if it is the same as 7th field.Signed-off-by: Masahiro Yamada
Acked-by: Otavio Salvador
19 Feb, 2014
1 commit
18 Feb, 2014
1 commit
14 Feb, 2014
1 commit
-
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.Signed-off-by: Gerlando Falauto
Cc: Karlheinz Jerg
Cc: Valentin Longchamp
Cc: Holger Brunck
Acked-by: Valentin Longchamp
07 Feb, 2014
2 commits
-
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMACSigned-off-by: Alexey Brodkin
Cc: Vineet Gupta
Cc: Francois Bedard
Cc: Wolfgang Denk
Cc: Heiko Schocher -
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)Signed-off-by: Alexey Brodkin
Cc: Vineet Gupta
Cc: Francois Bedard
Cc: Wolfgang Denk
Cc: Heiko Schocher
06 Feb, 2014
5 commits
-
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut
Cc: Albert Aribaud
Cc: Michael Schwingen
Cc: Tom Rini -
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut
Cc: Albert Aribaud
Cc: Michael Schwingen
Cc: Tom Rini -
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut
Cc: Albert Aribaud
Cc: Michael Schwingen
Cc: Tom Rini -
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut
Cc: Albert Aribaud
Cc: Michael Schwingen
Cc: Tom Rini -
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut
Cc: Albert Aribaud
Cc: Michael Schwingen
Cc: Tom Rini
04 Feb, 2014
2 commits
-
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.Signed-off-by: Tom Warren
Signed-off-by: Stephen Warren
Tested-by: Thierry Reding
Signed-off-by: Tom Warren -
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.Signed-off-by: Valentin Longchamp
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun
27 Jan, 2014
1 commit
-
Run "tools/reformat.py -i -d '-' -s 8 boards0.cfg && mv boards0.cfg boards.cfg"
in order to keep the entries sorted.Signed-off-by: Fabio Estevam
22 Jan, 2014
2 commits
-
u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.So, Increase the u-boot binary size to 768KB.
Signed-off-by: York Sun
Signed-off-by: Prabhakar Kushwaha -
Using the TPL/SPL method to booting from 8k page NAND flash.
- Add 256kB size SRAM tlb for second step booting;
- Add spl.c for TPL image boot;
- Add spl_minimal.c for minimal SPL image;
- Add C29XPCIE_NAND configure;
- Modify C29XPCIE.h for nand config and enviroment;Signed-off-by: Po Liu
Reviewed-by: York Sun
15 Jan, 2014
2 commits
-
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton .
Signed-off-by: Jon Nettleton
Signed-off-by: Fabio Estevam
14 Jan, 2014
2 commits
-
Signed-off-by: Albert ARIBAUD
Acked-by: Stefano Babic -
Signed-off-by: Albert ARIBAUD
Acked-by: Minkyu Kang
10 Jan, 2014
9 commits
-
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.Conflicts:
include/configs/exynos5250-dt.hSigned-off-by: Tom Rini
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM012:
- 1GB DDR3
- 64MiB Numonyx NOR flash
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
Cc: Stefan Roese -
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM013:
- 1GB DDR3
- 128 Mb Quad-SPI Flash(dual parallel)
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013ZC770 XM010:
- 1Gb DDR3
- 1Mb SST SPI flash
- 128 Mb Quad-SPI Flash
- 8 Mb SST SI flash
- Full size SD/MMC card cage
- 10/100/1000 Ethernet
- USB-UARTSigned-off-by: Jagannadha Sutradharudu Teki
-
MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switchFor more info - http://zedboard.org/product/microzed
Signed-off-by: Jagannadha Sutradharudu Teki
-
Zed is a complete development board based on the
Xilinx Zynq-7000 All Programmable SoC.APSOC:
- XC7Z020-CLG484-1
Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash(
- Full size SD/MMC card cage
Connectivity:
- 10/100/1000 Ethernet
- USB OTG (Device/Host/OTG)
- USB-UART
Expansion:
- FMC (Low Pin Count)
- Pmod. headers (2x6)
Video/Display:
- HDMI output (1080p60 + audio)
- VGA connector
- 128 x 32 OLED
- User LEDs (9)
User inputs:
- Slide switches (8)
- Push button switches (7)
Audio:
- 24-bit stereo audio CODEC
- Stereo line in/out
- Headphone
- Microphone input
Analog:
- Xilinx XADC header
- Supports 4 analog inputs
- 2 Differential / 4 Single-ended
Debug:
- On-board USB JTAG programming port
- ARM Debug Access Port (DAP)For more info - http://zedboard.org/product/zedboard
Signed-off-by: Jagannadha Sutradharudu Teki
-
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.ZC702-:
APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDsFor more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htmZC706-:
APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDsFor more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htmSigned-off-by: Jagannadha Sutradharudu Teki
-
zynq.h -> zynq-common.h, zynq-common is Common
configuration options for all Zynq boards.zynq.h is no longer exists hense removed from boards.cfg
Signed-off-by: Jagannadha Sutradharudu Teki
-
The vexpress_aemv8a is the first aarch64 board in U-Boot.
As it was introduced, it gets built when "MAKEALL -a arm"
is invoked, and fails as this command is run with a 32-bit,
not 64-bit, toolchain as the cross-compiler.Introduce 'aarch64' as a valid 'MAKEALL -a' argument, treated
as 'arm' for all other intents, and change the architecture
of the vexpress_aemv8a entry in boards.cfg from 'arm' to
'aarch64'.
09 Jan, 2014
2 commits
-
Signed-off-by: David Feng
Signed-off-by: Bhupesh Sharma
08 Jan, 2014
1 commit
-
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.Signed-off-by: Tom Rini
07 Jan, 2014
1 commit
06 Jan, 2014
3 commits
-
The board is similar to the standard km_kirkwood board. From a
u-boot point of view, the only difference is an increased
256 MiB DRAM (128M16). A board based on this design is for
example the SUP12.Signed-off-by: Karlheinz Jerg
Signed-off-by: Holger Brunck -
Conflicts:
include/micrel.hThe conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
03 Jan, 2014
1 commit
-
Signed-off-by: Shaohui Xie
30 Dec, 2013
1 commit
-
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.Signed-off-by: Rajeshwari S Shinde
Signed-off-by: Akshay Saraswat
Acked-by: Simon Glass
Signed-off-by: Minkyu Kang
