10 Oct, 2014
26 commits
-
Since on powerpc phys_size_t can be unsigned long long, this printout
line can result in a not nice compile warning.Signed-off-by: Valentin Longchamp
Acked-by: Simon Glass -
The lines COL (collision detect) and CRS (carrier sense) needs to be connected
and muxed to the CPSW MAC for a proper function in half-duplex Mode of the
interface.Signed-off-by: Hannes Petermaier
Cc: Tom Rini -
Fix the spelling of "configs".
Signed-off-by: York Sun
CC: Masahiro Yamada
Acked-by: Masahiro Yamada -
A SPL/TPL enabled target would was not recognized as
such by BSD sed, since it relies on a GNU extension.
Instead of or-ing just spell out both matches.Cc: Masahiro Yamada
Signed-off-by: Jeroen Hofstee
Acked-by: Masahiro Yamada -
remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.Signed-off-by: David Müller
-
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.Signed-off-by: David Müller
-
Signed-off-by: David Müller
-
Signed-off-by: David Müller
-
Signed-off-by: David Müller
-
Signed-off-by: David Müller
-
A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:Copyright 1994 - 2000 Neil Russell.
(See License)I analyzed the source code of LiMon v1.4.2 which was used for this
import. It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991. So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2. Mark them as such.Signed-off-by: Wolfgang Denk
-
Fix typo of commit d4e53f063dd25e071444b87303573e7440deeb89.
i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combinationSigned-off-by: Alexander Kochetkov
CC: Tom Rini
CC: Steve Kipisz -
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada
-
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada
-
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.Signed-off-by: Masahiro Yamada
-
This board has been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada
-
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada
-
In some cases, the last lines of SPL or TPL are not output to a file.
The entries remaining in the "unmatched" variable must be flushed.Signed-off-by: Masahiro Yamada
Acked-by: Simon Glass -
The definitions for div ratio supposed to be in hex and were added
in dec by mistake.Signed-off-by: Ivan Khoronzhuk
-
At least on OMAP, init_sata() no longer performs scsi_scan()
so we must do it explicitly here.Cc: Dan Murphy
Signed-off-by: Roger Quadros -
scsi_scan() must be called as part of scsi_init() and not
as part of sata_init().Signed-off-by: Roger Quadros
-
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.Signed-off-by: Roger Quadros
-
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional accessSigned-off-by: Roger Quadros
-
Commit 12cc54376768461533b55ada1b0b6d4979f40579 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.Signed-off-by: Stefan Herbrechtsmeier
-
Commit 294b91a5817147d4b7f47be2ac69bac2a1f26491 moved initr_malloc
earlier than initr_unlock_ram_in_cache. This causes issue on T4240.
It may be related to locked L1 d-cache and unlocked L2 cache. D-
cache could and should be unlock earlier for normal operation.This patch moves initr_unlock_ram_in_cache before initr_malloc. It
has been verified on the following boards, in which only T4240QDS
suffered and has been since fixed: T4240QDS, T2080QDS, P5040DS,
P4080DS, MPC8572DS, MPC8536DS, MPC8641HPCN, B4860QDS.Signed-off-by: York Sun
CC: Scott Wood
CC: Simon Glass
Acked-by: Simon Glass -
On a couple of platforms I've tripped over long PXE append lines overflowing
this array, due to having CONFIG_SYS_CBSIZE == 256. When doing preseeded Debian
installs it's pretty trivial to exceed that.Since the symptom can be a silent hang or a crash add a check. Of course the
affected boards would also need an increased CBSIZE to actually work.Note that due to the printing of the final bootargs string CONFIG_SYS_PBSIZE
also needs to be sufficiently large.Signed-off-by: Ian Campbell
[trini: Use %zd not %d in printf for all args]
Signed-off-by: Tom Rini
08 Oct, 2014
1 commit
-
In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.Reported-by: Karsten Merker
Signed-off-by: Hans de Goede
Tested-by: Karsten Merker
Tested-by: Zoltan HERPAI
Tested-by: Tony Zhang
Acked-by: Ian Campbell
07 Oct, 2014
8 commits
-
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.Signed-off-by: Anthony Felice
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner -
Signed-off-by: Tom Rini
-
Fix a trivial conflict in dw_mmc.c after talking with Marek.
Conflicts:
drivers/mmc/dw_mmc.cSigned-off-by: Tom Rini
-
Without NULL termination, various commands will read past the
end of input. In particular, this was noticed with error()
calls in cb_getvar and simple_strtoul() in cb_download.Since the download callback happens elsewhere, the 4k buffer
should always be sufficient to handle command arguments.Signed-off-by: Eric Nelson
-
This bit allows the MUSB controller to negotiate for high-speed mode when
the device is reset by the hub. If unset, Babble errors occur with
high-speed mass storage devices right after the first packet. This condition
is not caught by the interrupt handles in U-Boot, so no recovery is done,
and the USB communication is stuck.To fix this, set the bit unconditionally, not only for
CONFIG_USB_GADGET_DUALSPEED but also for host-only modes.Signed-off-by: Daniel Mack
06 Oct, 2014
5 commits
-
Enable and use the CONFIG_CMD_FS_GENERIC to avoid hard-coding the
filesystem type into the environment.Signed-off-by: Marek Vasut
Cc: Chin Liang See
Cc: Dinh Nguyen
Cc: Albert Aribaud
Cc: Tom Rini
Cc: Wolfgang Denk
Cc: Pavel Machek
Acked-by: Pavel Machek -
Split the SoCFPGA configuration into SoC-specific part which is
common for all boards (socfpga_cyclone5_common.h) and a board
specific part. There is currently only one board, which is the
generic SoCFPGA board (socfpga_cyclone5.h), but there are more
to come.This is necessary due to various features of the boards, which
unfortunatelly cannot be autodetected.Signed-off-by: Marek Vasut
Cc: Chin Liang See
Cc: Dinh Nguyen
Cc: Albert Aribaud
Cc: Tom Rini
Cc: Wolfgang Denk
Cc: Pavel Machek
Acked-by: Pavel Machek -
Reorganize and cleanup the configuration file for SoCFPGA. There
is no functional change after this cleanup. This was necessary,
since the file was a wild mess and it was impossible to make sense
of it's content, let alone change something without breaking some
other thing. This patch puts the contents on par with regular U-Boot
standards.Also remove unused preprocessor symbols CONFIG_SINGLE_BOOTOADER
and CONFIG_USE_IRQ, which is undefined by default. Finally, do
logical reordering of the defines in the file so it's much more
readable. The reordering was also necessary for the splitting
as the initial one was messy.Signed-off-by: Marek Vasut
Cc: Chin Liang See
Cc: Dinh Nguyen
Cc: Albert Aribaud
Cc: Tom Rini
Cc: Wolfgang Denk
Cc: Pavel Machek -
Add command to enable and disable the bridges between HPS and FPGA.
This patch does have a checkpatch issue with the assembler portion,
checkpatch correctly complains that there should be no whitespace
before quoted newline. I do not agree that fixing this specific
checkpatch issue will improve the readability, thus this one is not
addressed.Signed-off-by: Marek Vasut
Cc: Dinh Nguyen
Cc: Pavel Machek
Cc: Marek Vasut
Cc: Tom Rini
Cc: Albert Aribaud
Cc: Wolfgang Denk -
Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.Signed-off-by: Marek Vasut
Cc: Dinh Nguyen
Cc: Pavel Machek
Cc: Marek Vasut
Cc: Tom Rini
Cc: Albert Aribaud
Cc: Wolfgang Denk
Acked-by: Pavel Machek
