Eric Lee / smarc-uboot

11 Sep, 2003

2 commits

  • 7205e4075   * Patches by Denis Peter, 9 Sep 2003: ... Browse Code »

    add FAT support for IDE, SCSI and USB

    * Patches by Gleb Natapov, 2 Sep 2003:
    - cleanup of POST code for unsupported architectures
    - MPC824x locks way0 of data cache for use as initial RAM;
    this patch unlocks it after relocation to RAM and invalidates
    the locked entries.

    * Patch by Gleb Natapov, 30 Aug 2003:
    new I2C driver for mpc107 bridge. Now works from flash.

    * Patch by Dave Ellis, 11 Aug 2003:
    - JFFS2: fix typo in common/cmd_jffs2.c
    - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option
    - JFFS2: remove node version 0 warning
    - JFFS2: accept JFFS2 PADDING nodes
    - SXNI855T: add AM29LV800 support
    - SXNI855T: move environment from EEPROM to flash
    - SXNI855T: boot from JFFS2 in NOR or NAND flash

    * Patch by Bill Hargen, 11 Aug 2003:
    fixes for I2C on MPC8240
    - fix i2c_write routine
    - fix iprobe command
    - eliminates use of global variables, plus dead code, cleanup.

    wdenk
     
  • 149dded2b   * Add support for USB Mass Storage Devices (BBB) ... Browse Code »

    (tested with USB memory sticks only)

    * Avoid flicker on TRAB's VFD

    wdenk
     

06 Sep, 2003

1 commit

  • 7152b1d0b   * Add support for SK98xx driver ... Browse Code »

    * Add PCI support for SL8245 board

    * Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB)
    or 1 x AM29LV652 (two LV065 in one chip = 16 MB);
    Run IPB at 133 Mhz; adjust the MII clock frequency accordingly

    * Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz)
    to allow for more accurate baudrate settings
    (error now 0.7% at 115 kbps, instead of 3.5% before)

    * Patch by Andreas Mohr, 4 Sep 2003:
    Fix a lot of spelling errors

    wdenk
     

03 Sep, 2003

3 commits

01 Sep, 2003

1 commit

  • 326428cc8   Patch by Yuli Barcohen, 7 Aug 2003: ... Browse Code »

    According to the MPC8260 User's Manual, PCI_MODE signal should be
    reflected in SCCR register, and local bus pins configuration is taken
    from HRCW and appears in SIUMCR. For some reason it does not work
    this way, so the only possibility to detect if the board is
    configured in PCI mode is to check the BCSR. This patch sets SCCR and
    SIUMCR according to the BCSR.

    wdenk
     

30 Aug, 2003

3 commits

29 Aug, 2003

1 commit

28 Aug, 2003

3 commits

18 Aug, 2003

1 commit

08 Aug, 2003

1 commit

07 Aug, 2003

4 commits

06 Aug, 2003

2 commits

01 Aug, 2003

1 commit

27 Jul, 2003

1 commit

  • 1f4bb37d6   * Patch by Scott McNutt, 21 Jul 2003: ... Browse Code »

    Add support for LynuxWorks Kernel Downloadable Images (KDIs).
    Both LynxOS and BlueCat linux KDIs are supported.

    * Patch by Richard Woodruff, 25 Jul 2003:
    use more reliable reset for OMAP/925T

    * Patch by Nye Liu, 25 Jul 2003:
    fix typo in mpc8xx.h

    * Patch by Richard Woodruff, 24 Jul 2003:
    Fixes for cmd_nand.c:
    - Fixed null dereferece which could result in incorrect ECC values.
    - Added support for devices with no Ready/Busy signal hooked up.
    - Added OMAP1510 read/write protect handling.
    - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
    for non-JFFS2.
    - Switched default ECC to be JFFS2.

    wdenk
     

26 Jul, 2003

1 commit

25 Jul, 2003

1 commit

18 Jul, 2003

1 commit

  • 2535d6027   * Patch by Martin Krause, 17 Jul 2003: ... Browse Code »

    add delay to get I2C working with "imm" command and s3c24x0_i2c.c

    * Patch by Richard Woodruff, 17 July 03:
    - Fixed bug in OMAP1510 baud rate divisor settings.

    * Patch by Nye Liu, 16 July 2003:
    MPC860FADS fixes:
    - add MPC86xADS support (uses MPC86xADS.h)
    - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
    CONFIG_8xx_GCLK_FREQ
    - add DRAM SIMM not installed detection
    - use more "correct" SDRAM initialization sequence
    - allow different SDRAM sizes (8xxADS has 8M)
    - default DER is 0
    - remove unused MAMR defines from FADS860T.h (all done in fads.c)
    - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

    * Patch by Yuli Barcohen, 16 Jul 2003:
    support new Motorola PQ2FADS-ZU evaluation board which replaced
    MPC8260ADS and MPC8266ADS

    wdenk
     

17 Jul, 2003

2 commits

16 Jul, 2003

4 commits

15 Jul, 2003

2 commits

  • 6dff55297   * Patches by Martin Krause, 14 Jul 2003: ... Browse Code »

    - add I2C support for s3c2400 systems (trab board)
    - (re-) add "ping" to command table

    * Fix handling of "slow" POST routines

    wdenk
     
  • 8564acf93   * Patches by Yuli Barcohen, 13 Jul 2003: ... Browse Code »

    - Correct flash and JFFS2 support for MPC8260ADS
    - fix PVR values and clock generation for PowerQUICC II family
    (8270/8275/8280)

    * Patch by Bernhard Kuhn, 08 Jul 2003:
    - add support for M68K targets

    * Patch by Ken Chou, 3 Jul:
    - Fix PCI config table for A3000
    - Fix iobase for natsemi.c
    (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)

    * Allow to enable "slow" POST routines by key press on power-on
    * Fix temperature dependend switching of LCD backlight on LWMON
    * Tweak output format for LWMON

    wdenk
     

11 Jul, 2003

5 commits